User manual

Safety Measures for Operating the Security System

Please read carefully!

Before operating the security system, carefully read this manual and pay special attention to sections marked with an exclamation point Screenshot 2023-11-28 163123.png. To determine if this security system is suitable for your vehicle, refer to the vehicle manufacturer's requirements and operating instructions.

If you are unsure whether this security system is suitable for installation in your vehicle, return it to the seller within 14 days of purchase.

The security system is a complex technical device that requires connection to the vehicle's circuits associated with the engine operation.

Installation of the security system should only be performed by specially trained qualified professionals.

Mounting, programming, servicing, repairing, and disassembling/reassembling of the security system are prohibited for individuals who are not qualified specialists and have not undergone training and knowledge verification on safety procedures.

When programming the security system parameters, the set parameters must not contradict the requirements of the vehicle's operating instructions.

The user is fully responsible for any damage caused to individuals, animals, or property resulting from using the security system for purposes other than its intended use or in violation of the safety requirements outlined in this manual.

The manufacturer is not liable for losses and accidents caused by failure to comply with the safety rules and requirements outlined in this manual.

To avoid misunderstandings, keep the documents provided with the security system upon purchase. Verify the completion of the warranty card, including the sale date and seller's stamp. If there is no sale (purchase) date, the warranty period is calculated from the date of manufacture of the security system.

The service life of the security system is 5 years provided that the product is installed and operated in accordance with the operating instructions, installation guidelines, and wiring diagram.

If your security system includes a key fob or wireless tag:

The full electronic version of the instruction manual is available on the website help.starline.ru.

Mandatory Safety Measures When Using the Engine Start Function:

It is important to remember that a vehicle is a potential hazard. Section 12.8 of the traffic rules states: "The driver may leave their place or leave the vehicle if necessary measures are taken to prevent the vehicle from moving spontaneously or being used in the absence of the driver."

Before using the security system, carefully familiarize yourself with the safe use measures for remote or automatic engine start functions outlined below:

Before activating the remote or automatic engine start function:

Safety Measures When Charging Your Vehicle's Battery

Keep in mind that any battery charging process involves supplying a voltage higher than the nominal 12V to the battery and, consequently, to the vehicle's electrical system. This can damage the vehicle's electronic equipment and any additional equipment installed on your vehicle.

All of the above devices and modes can lead to uncontrolled delivery of high voltage (up to 25V to 60V) to the vehicle's electrical system, potentially damaging the electronic components of the security system and the vehicle's equipment.

Using jump-starting methods to charge the battery is not recommended. Even described "safe" jump-start methods are only safe for the donor vehicle. Connecting and disconnecting a fully discharged or faulty battery on your vehicle with the engine running can damage your vehicle's electronic devices and security system due to voltage spikes caused by connecting and disconnecting the battery.

In the event of using the aforementioned devices and modes, the responsibility for damage to electronic equipment lies with the vehicle owner.

Follow safe battery charging procedures!

Before charging, the battery terminals must be disconnected from the vehicle's electrical system. Only then can you begin the battery charging process. After charging, reconnect the battery to the vehicle's electrical system.

This necessity arises because without measuring devices, you cannot determine the condition, state, or reason for battery discharge (such as internal short circuits or breaks). Connecting a charging device to a faulty battery poses a risk of damaging the vehicle's electronic equipment and security system due to increased voltage.

General Description

The StarLine A90, Starline A60 security-telematics complexes (hereinafter referred to as the complex) are designed to protect motor vehicles from theft and armed attacks. 

The complex is controlled using a remote key.

Key Features

  • Built-in audible notifier for convenient owner notification.
  • "Slave" mode operation (arming or disarming the security mode with the vehicle's factory key fob).
  • Additional owner authorization via wireless tag, smartphone (availability depends on the complex configuration), or secret code entry using factory buttons.
  • StarLine control dialogue code with individual 128-bit encryption keys, ensuring reliable protection against all known code grabbers.
  • Remote and automatic engine control (A90).
  • Remote control of engine preheating devices.
  • Bypassing the factory immobilizer using a factory immobilizer disable module (analog connection).
  • Service button combined with an LED system status indicator.
  • Universal reassignable inputs/outputs.
  • Special StarLine Master application allowing for individual complex customization based on owner preferences and vehicle features, and firmware updates.

Pin Envelope

pinEnvelope.jpg

The supply kit includes a pin envelope with the following information:

Do not disclose the Emergency Disarm Code to anyone! Remember that knowing the Emergency Disarm Code, an intruder could deactivate the protective functions.

Technical Specifications

Parameter Value
Remote Key Operating Frequency 868.7–869.2 MHz
Remote Key Control Range Up to 1500 meters
Notification Range on Remote Key Up to 2000 meters
Interfaces
  • 1 Universal StarLine Bus
  • 1 USB
  • 23 Configurable Channels which can be used as:
    • 11 Outputs (0.2 A)
    • 1 Output (2 A)
    • 3 Positive Inputs
    • 3 Negative Inputs
    • 1 Universal Input
  • Temperature Sensor Connector
  • Service Button Connector
  • Microphone Connector
Input Voltage Range 8–16 V
Power Consumption 8.7 mA
Operating Temperature Range -40°C to +85°C
Main Unit Dimensions 130 x 60 x 22 mm
Weight 95 grams

Light and sound indication

The security complex provides various options for indicating modes such as "Disarmed", "Armed", and "Alarm":

The default setting includes sound notifications with sirens and emergency light signals. The indicator mode is configured by the installation specialist during complex setup.

Indicator table

The security complex informs about its status by means of sound (horn) and light signals (turn signals):

Event Light signals Horn
Security activation
icon-short.png
icon-short.png
Security activation with security zone breach
icon-short.png icon-short.png icon-short.png icon-short.png
icon-short.png icon-short.png icon-short.png icon-short.png
Security deactivation
icon-short.png icon-short.png
icon-short.png icon-short.png
Security deactivation (one of the zones was violated in the security cycle)
icon-short.png icon-short.png icon-short.png
icon-short.png icon-short.png icon-short.png
Alarm

30 s

30 s

Warning level alarm

icon-short.png icon-short.png icon-short.png icon-short.png icon-short.png icon-short.png
icon-short.png icon-short.png icon-short.png
Panic 10 s 10 s
Trunk opening icon-short.png icon-short.png
Exit from service mode
icon-short.png icon-short.png
icon-short.png icon-short.png

LED Indicator

System State LED Indicator
Disarmed Not lit
Disarmed with ignition and one zone violation (door, hood, trunk) Once every 5 seconds
Armed Once per second
Engine Running Constantly lit
Service Mode Not lit
"Trip Prohibition" Function Enabled Not lit
Anti-hijacking Mode Enabled 10 times per second
Incorrect Emergency Disarm Code Entered Four times
Emergency Disarm Code Entry Blocked for 15 minutes Five times
Correct Emergency Disarm Code Entered Twice

Sound Indicator

Event Sound Indicator
Waiting for Authorization 10 seconds
Successful Owner Authorization Code Input icon-short.png icon-short.png
Incorrect Owner Authorization Code Input icon-short.png icon-short.png icon-short.png icon-short.png

Controlling the system using a remote key

Remote Keys

The complex's memory can be programmed with two types of remote keys:

  1. Remote key with LCD (liquid crystal display). 

    image.png     image.png

    The remote key with LCD uses a AAA 1.5 V battery. The battery life of the remote key with LCD is up to 6 months depending on operating conditions.
  2. Additional remote key.
    a96-led-remote.jpg
    The additional remote key uses a CR2032 3 V battery.
    The battery life of the additional remote key is up to 1 year depending on operating conditions.

The presence of an additional remote key depends on the configuration of the security system.

The main and additional remote keys are equivalent in cryptographic resistance. Both remote keys use a dialogue algorithm for data exchange, excluding intelligent electronic hacking.

Information about the current state of the security complex is transmitted to the main remote key and displayed on the screen. The additional remote key does not have notification functions; it is intended only for transmitting basic control commands.

Meaning of icons on the remote key

Engine Start

Icon Meaning

Двигатель запущен.jpg

Engine is running

Включен автоматический запуск по будильнику.jpg

Automatic start by alarm is activated

Включен автоматический периодический запуск.jpg

Automatic periodic start is activated

Включен автоматический запуск по температуре.png

Automatic start by temperature is activated

Включен автоматический запуск по падению напряжения АКБ.png

Automatic start by battery voltage drop is activated

Выполнена программная нейтраль.png

Programmed neutral is executed

Включен подогрев двигателя (мигает).png

Engine heating is activated (blinking)

Operating Modes

Icon Meaning

Автомобиль под охраной_2.png

Security on

Режим «Свободные руки».png

"Hands-Free" mode

Сервисный режим.png

Service mode

Режим настроек и программирования.png

Settings and programming mode

Блокировка кнопок брелока.png

Remote key button lock

Режим «Антиограбление».png

"Anti hijack" mode

Security zones

Icon Meaning

Включено зажигание.png

Ignition is on

Затянут стояночный тормоз.png

Parking brake is engaged

открыт капот.png

Hood is open

Открыта дверь.png

Door is open

Открыт багажник.png

Trunk is open

Sensors

Icon Meaning

Сработал датчик наклона или движения.png

Tilt or motion sensor activated

Сработал дополнительный датчик 1.png

Additional sensor 1 activated

Сработал дополнительный датчик 2.png

Additional sensor 2 activated

Сработал датчик наклона.png

Tilt sensor activated

Сработал датчик движения.png

Motion sensor activated

Сработал предупредительный уровень датчика удара.png

Warning level of shock sensor activated

Сработал тревожный уровень датчика удара.png

Alarm level of shock sensor activated

Датчик удара отключен.png

Shock sensor is deactivated

Additional Information

Icon Meaning

Передача данных_2.png

Data Transmission

Замените батарейку в брелоке_2.png

Replace battery in remote key

Звук сирены включен_2.png

Siren is on

Сирена отключена_2.png

Siren is off

Main control commands from remote key

Numbering of buttons on the main remote key:

брелок E96.png

Numbering of buttons on the additional remote key:

dop-brelok.png

The following terms of button press duration are used in this manual:

Short Press

Pressing a single button (or two buttons simultaneously) for less than 1.5 seconds.

Example: icon-short-1.png — short press of the first button; icon-short-double-2-3.png — short press of buttons 2 and 3 simultaneously.

Long Press

Pressing and holding a button or two buttons until a melodic sound signal and vibration signal appear.

Two levels of long press are provided:

  • First-level long press — pressing a button until the first sound signal.

    Examples: icon-long-1.pngicon-note-1.png — first-level long press of the first button; icon-long-double-1-2.pngicon-note-1.png — first-level long press of the first and second buttons;

  • Second-level long press — pressing a button until the second sound signal;

    Examples: icon-long-4.pngicon-note-2.png — second-level long press of the fourth button.
Double Press

Two presses of the same button within 1 second.

Example: icon-short-1.pngicon-short-1.png — double press of the first button.

Triple Press

Three presses of the same button within 1 second.

Example: icon-short-1.pngicon-short-1.pngicon-short-1.png — triple press of the first button.

Sequential Press

Two presses of one or different buttons. The first press should be long (first or second level), the second press should be short. Release the first button before the second press.

Example: icon-long-2.pngicon-note-1.pngicon-short-1.png — sequential press of buttons 2 and 1.

Main control commands from remote key:

Command Button Combination
Arm
icon-short-1.png
Arm without confirmation sound signals

icon-short-1.pngicon-short-1.pngicon-short-1.png

Disarm
icon-short-2.png

Disarm without confirmation sound signals

icon-short-2.pngicon-short-2.pngicon-short-2.png

Request engine temperature, cabin temperature, battery voltage, fuel level. During automatic engine start - remaining engine runtime.
icon-short-3.png

Start engine

icon-long-1.pngicon-note-1.png

Stop engine

icon-long-2.pngicon-note-1.png

Activate engine pre-heater

icon-long-2.pngicon-note-1.pngicon-short-1.png

Deactivate engine pre-heater

icon-long-2.pngicon-note-1.pngicon-short-2.png

Search for vehicle in parking lot

icon-long-3.pngicon-note-1.png

Activate/deactivate shock sensor

icon-long-1.pngicon-note-1.pngicon-short-2.png

Activate/deactivate tilt and motion sensor

icon-long-1.pngicon-note-1.pngicon-short-3.png

Activate "Panic" mode

icon-short-1.pngicon-short-1.png

Unlock trunk

icon-short-2.pngicon-short-2.png
Activate automatic start cursor menu
Activate/deactivate service mode
icon-service-mode.png or cursor menu
Activate/deactivate "Hands-Free" mode cursor menu

Activate/deactivate button lock

icon-short-double-2-3.png

Activate/deactivate "Button Autolock" function

icon-long-double-1-4.pngicon-note-2.png

Activate only remote key vibration signal

icon-long-3.pngicon-note-1.pngicon-short-3.png

Activate sound profile "SOUND 2"

icon-long-3.pngicon-note-1.pngicon-short-1.png

Activate sound profile "SOUND 1"

icon-long-3.pngicon-note-1.pngicon-short-2.png

Activate sound profile "SOUND 0"

icon-long-3.pngicon-note-1.pngicon-short-3.png

Activate sound profile "SOUND --"

icon-long-3.pngicon-note-1.pngicon-short-4.png

Launch flexible logic program


icon-short-3.pngicon-short-3.png

Cursor Menu

Some functions of the security complex are controlled through a cursor menu: control of the "Hands-Free" mode, service mode, setting the automatic engine start.

Entering and exiting the menu is done by long-pressing button 4: icon-long-4.pngicon-note-1.png. If no buttons on the remote key are pressed within 15 seconds, there will be an automatic exit from the menu. When entering the menu, the cursor will be set to the first icon. Transition to the next and previous menu items is done by short pressing buttons icon-short-1.png or icon-short-4.png, respectively. 

Selecting a function is done by short pressing buttons 2 and 3: icon-short-double-2-3.png.  Changing the parameter value is done by short pressing buttons icon-short-2.png or icon-short-3.png (decrease and increase, respectively). Holding the button for a long time increases the speed of changing the parameter value.

Transitions between menu items, changing parameters, and exiting the menu will be confirmed by a melodic sound signal.

Descriptions and management of settings are provided in the table.

 Icon Parameter Description Setting Step
Режим «Свободные руки».png
"Hands-Free" mode Enable/disable "Hands-Free" mode
Включен автоматический запуск по будильнику.jpg
Automatic engine start and preheater start by alarm clock

Set the hours and minutes for engine start.

Switching between engine and preheater start settings is done by short pressing buttons 1_2.png and 3_4.png on the remote key.

When setting the engine start, the screen will display the digit "1", for preheater start — the digit "2".

1 minute
Включен автоматический периодический запуск.jpg

Automatic start by timer

Set the frequency of engine start in hours 1 hour
Включен автоматический запуск по температуре.png
Automatic start by temperature Set the temperature value in degrees Celsius 1 ºС
Включен автоматический запуск по падению напряжения АКБ.png
Automatic start by voltage Set the battery voltage value in Volts 0.1 V
Сервисный режим.png
Service mode Enable/disable service mode

Settings Menu

The settings menu is intended for configuring the complex operation parameters.

Entering and exiting the settings menu is done by long-pressing button 4: icon-long-4.pngicon-note-2.png. After entering the menu, the current state of the complex settings will appear on the remote key screen:

image.pngimage.pngimage.png

Transition to menu items is done by short pressing buttons icon-short-1.png or icon-short-4.png, to the previous and next item, respectively.

Decreasing and increasing the parameter value is done by short pressing buttons icon-short-2.png or icon-short-3.png, respectively. The longer the press, the more units the value changes.

Changing the parameter and exiting the menu will be confirmed by a melodic sound signal, transitions between menu items — by a vibration signal.

Setting the Time Zone

To set the time zone, select the first item in the settings menu. Then, using buttons icon-short-2.png and icon-short-3.png set the desired value. The minimum step size is 1 hour.

Setting Light and Sound Indicators for Arming and Disarming

To configure the operation of light and sound indicators when arming and disarming, select the second item in the settings menu. Then, using buttons icon-short-2.png and icon-short-3.png  set the desired value.

Description of configuration options:

Setting Siren Volume for Arming and Disarming

To set the siren volume level, select the third item in the settings menu. Then, using buttons icon-short-2.png and icon-short-3.png, select the desired siren volume level.

0 — no sound, 10 — maximum volume level.

Setting Light and Sound Indicators in "Alarm" Mode

To configure light and sound indicators in "Alarm" mode, select the fourth item in the settings menu. Then, using buttons icon-short-2.png and icon-short-3.png, set the desired value.

Description of configuration options:

Setting Siren Volume in "Alarm" Mode

To set the siren volume in "Alarm" mode, select the fifth item in the settings menu. Then, using buttons icon-short-2.png and icon-short-3.png, set the desired siren volume level.

0 — no sound, 10 — maximum volume level.

Setting Motion Sensor Sensitivity

To adjust the motion sensor sensitivity level, select the sixth item in the settings menu. Then, using buttons icon-short-2.png and icon-short-3.png, set the desired value from 0 to 30.

0 — sensor disabled, 30 — maximum sensitivity level.

Setting Tilt Sensor Sensitivity

To adjust the tilt sensor sensitivity level, select the seventh item in the settings menu. Then, using buttons icon-short-2.png and icon-short-3.png, set the desired value from 0 to 30.

0 — sensor disabled, 30 — maximum sensitivity level.

Setting Warning Shock Sensor Sensitivity

To adjust the pre-warning shock sensor sensitivity level, select the eighth item in the settings menu. Then, using buttons icon-short-2.png and icon-short-3.png, set the desired value from 1 to 30.

0 — sensor disabled, 30 — maximum sensitivity level.

The selected pre-warning shock sensor sensitivity value must be greater than the alarm shock sensor sensitivity value.

Setting Alarm Shock Sensor Sensitivity

To adjust the alarm shock sensor sensitivity level, select the ninth item in the settings menu. Then, using buttons icon-short-2.png and icon-short-3.png, set the desired value from 0 to 29.

0 — sensor disabled, 29 — maximum sensitivity level.

The selected alarm shock sensor sensitivity value must be lower than the pre-warning shock sensor sensitivity value.

Setting Tag Loss Zone Range

To set the range of the tag loss zone, select the tenth item in the settings menu. Then, using buttons icon-short-2.png and icon-short-3.png, set the desired value from 3 to 10.

3 — minimum range, 10 — maximum range.

The tag loss zone range should be greater than the tag detection zone range.

Ensure that the set tag loss zone range is sufficient from all sides of the vehicle.

Setting Tag Detection Zone Range

To set the range of the tag detection zone, select the eleventh item in the settings menu. Then, using buttons icon-short-2.png and icon-short-3.png, set the desired value from 1 to 8.

1 — minimum range, 8 — maximum range.

The detection zone should be smaller than the tag loss zone range.

Setting the Communication Check Period with the Remote Key

To set the communication check period with the remote key, select the twelfth item in the settings menu. Then, using buttons icon-short-2.png and icon-short-3.png, select the value 0 or 1.

Description of configuration options:

Remote Sound Profile Menu

The menu offers 4 sound profiles with settings for various types of remote signals: command confirmation, alarm, and button press. Profile selection is done by pressing buttons on the remote.

The sound profile settings shown in the table are set by default.

Profile Name Button Combination

Description

1 SOUND 2

icon-long-3.pngicon-note-1.pngicon-short-1.png

Maximum volume with all signals, vibration signal enabled.
2 SOUND1
icon-long-3.pngicon-note-1.pngicon-short-2.png
Minimum volume with all signals, vibration signal enabled.
3 SOUND 0
icon-long-3.pngicon-note-1.pngicon-short-3.png
Vibration signal only, sound volume disabled.
4 SOUND --
icon-long-3.pngicon-note-1.pngicon-short-4.png
Silent mode, sound volume and vibration signal disabled.

Adjusting Sound Profile Settings:

Enter the menu by long press of the button icon-long-3.pngicon-note-2.png. After entering, the current profile settings will be displayed.

Adjusting Command Confirmation Volume

image.png  image.png

Volume adjustment is done by short pressing the buttons icon-short-2.png or icon-short-3.png, respectively. A short press of the button icon-short-4.png enables or disables the vibration signal.

To switch to adjusting the next type of signal within the selected sound profile, press icon-short-1.png.

Adjusting Alarm Signal Volume

image.pngimage.png

Volume adjustment is done by short pressing the buttons icon-short-2.png or icon-short-3.png, respectively. A short press of the button icon-short-4.png enables or disables the vibration signal.

To switch to adjusting the next type of signal within the selected sound profile, press icon-short-1.png.

Adjusting Button Press Signal Volume

image.pngimage.png

Volume adjustment is done by short pressing the buttons icon-short-2.png or icon-short-3.png, respectively. A short press of the button icon-short-4.png enables or disables the vibration signal.

To switch to adjusting the next type of signal within the selected sound profile, press icon-short-1.png.

Exiting the menu automatically occurs after 10 seconds without pressing any buttons on the remote. After exiting, the name of the set profile will be displayed on the screen for several seconds:

image.png

Resetting Profile Settings to Factory Defaults

To reset profile settings to factory defaults, follow these steps:

  1. Select the desired sound profile using the corresponding button combination.
  2. Enter the sound profile menu by second-level long press of the 3 button: icon-long-3.pngicon-note-2.png.
  3. Repeat the second-level long press of the 3 button: icon-long-3.pngicon-note-1.pngicon-note-1.png.

Selecting a Sound Theme

In the sound profile menu, you can also set the tone of the remote key's sound signals by selecting one of the sound themes. To select a sound theme, follow these steps:

  1. Enter the sound profile menu by performing a second-level long press on button 3: icon-long-3.pngicon-note-2.png.
  2. Briefly press buttons icon-short-double-2-3.png simultaneously. The screen will display the name of the sound theme: BR-1 or BR-2.
  3. Briefly press buttons icon-short-double-2-3.png simultaneously to select the next sound theme.

By default, the BR-1 theme is set

You will automatically exit the menu after 10 seconds if no buttons on the remote key are pressed

Automatic Button Lock Function

When this function is activated, the remote key buttons are automatically locked after the backlight turns off. The function is enabled and disabled by performing a second-level long press on buttons 1 and 4: icon-long-double-1-4.pngicon-note-2.png.

Remote Key Locator Function

To locate the remote key, hold the service button for 5 seconds — the remote key will emit a sound signal.

Setting Time and Date

To set the current time and date, follow these steps:

  1. Enter the time and date settings menu by sequentially pressing button 4: icon-long-4.pngicon-note-1.pngicon-short-4.png.
  2. Use a short press of button icon-short-2.png to set the hours and a short press of button icon-short-3.png to set the minutes.

    image.pngimage.png


    • 1 — Hours;
    • 2 — Minutes.
  3. Briefly press button icon-short-1.png to proceed to set the current date.

    image.pngimage.png


    • 1 — Day;
    • 2 — Month;
    • 3 — Year.
  4. Use a short press of button icon-short-2.png to set the current day, a short press of button icon-short-3.png to set the current month, and a short press of button icon-short-4.png to set the current year.
  5.  To exit the menu, press buttons icon-short-double-2-3.png simultaneously.

Operating Modes

Security modes


Armed
Disarmed
Antihijack
Alarm
Panic
Additional modes



Hands-Free
Service mode
Device registration

Security modes provide protection for the vehicle against theft.

Additional modes are intended for adding new devices ("Device Registration" mode), disabling security functions for vehicle servicing ("Service Mode"), and convenient system control ("Hands-Free" mode).

Armed Mode

In "Armed" mode, the following zones are monitored:

If any of these zones are breached, the system will switch to "Alarm" mode.

Arming is only possible with the ignition off. If the arming command is sent while the ignition is on, only the central lock will be activated.

Arming can be activated in one of the following ways:

Successful arming will be confirmed by 1 sound signal and 1 light signal.

If the doors, hood, or trunk are not properly closed, or if any of the door, hood, or trunk switches are faulty (permanently closed), the system will warn you with 4 sound signals and 4 light signals. Restore the breached security zone and check for a single confirming signal indicating entry into the armed mode.

Silent Arming

Silent arming, which does not use sound signals (siren), can be performed by triple press on button icon-short-1.png of the remote key;

Successful arming will be confirmed by 1 light signal.

If the doors, hood, or trunk are not properly closed, or if any of the door, hood, or trunk switches are faulty (permanently closed), the system will warn you with 4 light signals. Restore the breached security zone and check for a single confirming signal indicating entry into the armed mode.

Emergency Arming

If the tag or remote key battery is dead, and there is no access to the starline.online personal account and StarLine mobile app, use emergency arming:

  1. Press the service button or the transceiver button 3 times.
  2. Turn on the ignition. Three sound signals will follow.
  3. Check for two short sound signals.
  4. Turn off the ignition.
  5. Exit the vehicle and close all doors.

Disarmed Mode

Disarming can be performed in one of the following ways:

Successful disarming will be confirmed by 2 sound signals and 2 light signals. If the "Alarm" mode was activated during the armed state, 3 sound signals and 3 light signals will follow.

After disarming, all events that occurred during the armed state will be displayed on the remote key screen.

If no actions are taken within 30 seconds after disarming, the system will automatically switch to "Armed" mode and lock the central locking system.

Silent Disarming

Silent disarming, which does not use sound signals (siren), can be performed by triple press on button icon-short-2.png of the remote key;

Successful silent disarming will be confirmed by 2 light signals. If the "Alarm" mode was activated during the armed state, 3 light signals will follow.

After disarming, all events that occurred during the armed state will be displayed on the remote key screen.

If no actions are taken within 30 seconds after disarming, the system will automatically switch to "Armed" mode and lock the central locking system.

Central Locking During Travel Function

This function is designed for automatically locking the central locking system during a trip based on one of the configurable conditions:

Enabling, disabling, and configuring the "Central Locking During Travel" function is performed by an installation specialist.

Central Lock Unlocking During Travel Function

This function is designed for automatically unlocking the central locking system during a trip based on one of the configurable conditions:

Enabling, disabling, and configuring the "Central Lock Unlocking During Travel" function is performed by an installation specialist.

Trunk Unlocking in Armed Mode Function

This function allows the trunk to be opened with the standard vehicle remote key without disarming the system, provided that the tag and/or the system's remote key is within range.

Enabling, disabling, and configuring the "Trunk Unlocking in Armed Mode" function is performed by the installation specialist during setup.

Keyless Entry System Lock Function

To use this function, tag authorization must be enabled.

The "Keyless Entry System Lock" function provides an additional level of protection against theft in case the standard vehicle key is stolen. In the "Armed" mode, the system blocks the operation of the keyless entry system when the tag is out of range.

By default, the "Keyless Entry System Lock" function is disabled. Contact an installation specialist to activate it.

Alarm Mode

The "Alarm" mode is activated when any of the zones in the "Armed" mode is breached. The system will trigger the siren and the hazard lights for 30 seconds and notify the owner via the remote key. If the zone is not restored, the system will repeat the alarm cycle one more time.

When one of the warning zones is breached, 3 sound signals and 3 light signals will follow.

Resetting the "Alarm" mode without disarming the system is done by a short press on buttons icon-short-1.png or icon-short-2.png on the remote key.

Notification options is configured by an installation specialist:

By default, sound notification with siren and hazard lights is enabled.

The maximum number of zone activations is limited to 8 cycles per arming period.

Panic Mode

The "Panic" mode is designed to ensure the safety of the owner and the vehicle.

This mode is activated by the owner’s command via a double press on button 1 of the remote key (icon-short-1.pngicon-short-1.png). Upon receiving the command, the system activates the siren and hazard lights for 10 seconds to attract attention.

This mode can also be used to locate the vehicle in a parking lot.

Anti-Hijack Mode

The "Anti-Hijack" mode is designed to protect the driver from robbery during driving. The system switches to this mode either by the owner’s command or when the tag/remote key is not detected.

The algorithm works as follows:

The exit from the "Antihijack" mode due to the disappearance of the tag or remote control can be done in one of the following ways:

If the emergency disarm code is entered incorrectly 3 times, the ability to enter the code will be blocked for 15 minutes, and the owner will receive an SMS notification.

By default, the "Anti-Hijack" by tag or remote key loss option is disabled. To enable it, hold the tag button until a long red flash appears, then release the button.

Hands-Free mode

The "Hands-Free" mode is designed for automatic enabling/disabling of the security mode.

You can enable or disable the "Hands-Free" mode in the cursor menu of the remote key by selecting the corresponding item;

By default, the "Hands-Free" mode is disabled. All mode operation parameters are configured by the installation specialist during installation.

There are several options for enabling and disabling the alarm in the "Hands-Free" mode:

By default, the tag's operating range is set to the maximum value. To change it, please contact an installation specialist.

If the tag is lost from view while the doors, hood, or trunk are open, the system will notify about this event in one or more of the following ways:

If the connection is lost or the tag's power element is depleted during the trip, but an event is recorded inside the cabin, the system will ignore the tag signal loss. Ten seconds after the door is opened, the system will automatically switch to the "Alarm" mode.

In the "Hands-Free" mode, automatic arming will not be executed if the tag is within sight.

Disabling "Hands-Free" Mode for 1 Security Cycle

If the tag remains within range during parking (for example, you're in a cafe while your car is parked nearby), it is recommended to disable the security deactivation in "Hands-Free" mode for 1 security cycle. After completing the security cycle, the system will automatically return to its previous operating mode after opening one of the doors, the trunk, or the hood.

You can disable the security deactivation in "Hands-Free" mode for 1 security cycle using one of the following methods:

Successful disabling of the "Hands-Free" mode for 1 security cycle will be confirmed by 1 audible signal.

If the system is in the "Disarmed" mode while the vehicle owner is nearby (for example, unloading the trunk at the cottage), it is recommended to disable the security activation in "Hands-Free" mode for 1 security cycle. After turning on the ignition or sending the "Arm" command, the system will automatically return to its previous "Hands-Free" mode.

You can disable the security activation in "Hands-Free" mode for 1 security cycle using one of the following methods:

Successful disabling of the "Hands-Free" mode for 1 security cycle will be confirmed by 1 audible signal.

Service mode

Service Mode is intended for temporarily disabling security functions and restricting access to system settings. It is recommended during service maintenance.

Enabling Service Mode is only possible from the "Disarmed" mode near the vehicle.

The following functions and modes are unavailable in Service Mode:

You can enable and disable the Service Mode using one of the following methods:

Entering Service Mode will be confirmed by a yellow LED indication on the tag.

In Service Mode, transition to other additional modes is prohibited!

Automatic Exit from Service Mode

For this function to work, owner authorization must be enabled, sensors must be activated, and vehicle speed information must be available.

The system will automatically exit Service Mode and wait for owner authorization when leaving the service station based on the established event with the ignition on. After successful authorization, the system will switch to the "Disarmed" mode.

If authorization fails, the security system will switch to the "Alarm" mode.

Immobilizer mode

The Immobilizer Mode prevents movement without additional owner authorization.

Upon disarming or turning off the ignition, the system will wait for authorization confirmation either by the presence of the key fob in the vicinity or by entering the owner's authorization code using the vehicle's standard buttons (e.g., multimedia or window control buttons) while the ignition is on.

If owner authorization is not confirmed within 1 minute, attempting to start the engine will result in it being locked for 1 minute or until the owner's authorization is successfully completed.

When the Immobilizer Mode is enabled alongside the "Slave" mode, both authorization conditions must be met to disarm the system.

Vehicle Status Control

With this function, users can request information such as engine and cabin temperature, battery voltage, and fuel level.

Requests can be made by the owner with a short press of the remote key button icon-short-3.png.

The information will be displayed on the remote key's screen.

The engine temperature readings displayed by the system depend on the location of the engine temperature sensor and may differ from those shown on the vehicle's dashboard.

If the request is made during automatic engine start, the remaining engine runtime will also be displayed in addition to the aforementioned values.

Engine Start Function

The engine start function allows remote and automatic engine starting/stopping.

Preparing a Manual Transmission (MT) Vehicle for Remote and Automatic Engine Start

Before starting the engine, you need to perform the "Program Neutral" procedure:

  1. Engage the parking brake while the engine is running.
  2. Remove the key from the ignition switch. The engine will continue to run.
  3. Exit the vehicle, close the doors, trunk, and hood, and arm the security system. The engine will be stopped.
  4. The system will enter the "Armed" mode.
  5. The key fob will display the "N" icon.
  6. The system is now ready for remote and automatic engine start.

If a door is opened or the ignition is turned on after performing the "Program Neutral" procedure, remote and automatic engine start will be canceled until the next "Program Neutral" algorithm execution.

Preparing an Automatic Transmission (AT) Vehicle for Remote and Automatic Engine Star

Ensure that the AT selector is in the "Park" position.

Engine Start

Remote engine start can be initiated by one of the following methods:

Automatic engine start can occur under the following conditions:

Temperature and battery voltage values, interval, and schedule are set in the remote key cursor menu.

The minimum engine runtime for remote start is 10 minutes. To change it, please consult an installation specialist.

Automatic engine start will not occur if less than 1 hour has passed since the last start or if the previous automatic start failed.
After a trip, automatic engine start is possible no earlier than 5 minutes after the engine has been stopped.

Engine Stop

The engine stops if:

Car driving continuation after remote engine starting

To continue driving the car, without stopping the engine after remote starting, do as follows:

Several options are possible depending on the car and complex connection method:

(*) Ask the installation specialist during mounting about the connection method of your complex and the operation algorithm.

Function «Engine starting preheater»

The function allows for engine preheating before starting. The starting preheater can be controlled both in the manual and automatic mode.

Manual mode

In the manual mode the starting preheater is switched on/off by a command.

The starting preheater can be switched on by sequentially pressing buttons 2 and 1 on the remote key: icon-long-2.pngicon-note-1.pngicon-short-1.png.

The preheater operates for 20 minutes in this mode. To change its duration, consult your installation specialist.

If the preheater has factory settings different from those set by the installation specialist, the operating time may differ from the specified time.

Operation can be prolonged by sending a repeated command for starting preheater switch-on.

The starting preheater can be switched off by sequentially pressing button 2 on the remote key: icon-long-2.pngicon-note-1.png icon-short-2.png.

To protect the engine from overheating, the preheater will stop when the maximum temperature threshold specified during the security system setup is reached. This helps protect the engine from overheating.

Automatic mode

The automatic mode is activated by the installation specialist during complex setting after mounting.

In automatic mode, the preheater is activated before remote and/or automatic engine start.

Automatic engine start can occur under the following conditions:

The temperature value and schedule are set in the remote key cursor menu.

If the engine temperature before remote or automatic start is lower than the set value, the preheater will start. When the engine reaches the set temperature (during automatic start) or after the set time elapses, the engine will start.

The preheater is turned off after the set time elapses or when the temperature threshold for disconnection is reached.

The preheater operates for 10 minutes in this mode. To extend the operation, you need to manually send the command to turn on the preheater.
To adjust the operation time and temperature threshold for preheating, please consult an installation specialist.

«Turbotimer» function

For vehicles with turbochargers, use the "Turbotimer" function to cool the engine turbine.

The "Turbotimer" function is activated by the installation specialist during installation.

To activate the function on vehicles with an ignition key, follow these steps:

To activate the function on vehicles with a START/STOP button, follow these steps:

The cooling time for the turbine is calculated automatically and depends on the engine speed before the end of the trip. The maximum turbine cooling time is 5 minutes.
For vehicles with a START/STOP button, the turbotimer operation time is automatically extended until the system enters the "Armed" mode.

Beach mode

In "Beach Mode," there is no need for a tag or key fob to enable/disable the security system (they can be left inside the car). Owner authorization is achieved by entering the emergency disarm code by touching the door handle with a capacitive sensor StarLine ES-1 (optional). In this mode, the system does not respond to key fob commands.

To activate "Beach Mode," follow these steps:

  1. Switch the system to the "Disarmed" mode and turn off the ignition.
  2. Press the service button three times and turn on the ignition. This will be followed by three audible signals confirming the activation of "Beach Mode." Turn off the ignition.
  3. Exit the car and touch the door handle three times. The system will enter the "Armed" mode.

"Beach Mode" deactivates the "Hands-Free" mode until the security system is turned off.

Exiting the mode is done by entering the emergency disarm code by touching the door handle with an interval of no more than 3 seconds. The correct input of the code digit will be confirmed by audible and visual signals, the quantity of which will correspond to the code digit. The correct input of the code will be confirmed by 2 audible and visual signals.

If the emergency disarm code is entered incorrectly 3 times, the possibility of re-entering the code will be blocked for 15 minutes.

After disarming the system, if no actions or commands are given, the system will automatically switch to the "Armed" mode after 30 seconds, and the "Beach" mode will remain active.

Video recorder control

The "Video Recorder Control" function is activated by the installation specialist during the installation of the system.

The system automatically activates the video recorder for recording in the following cases:

If the engine is started when the "Armed" mode is activated, the video recorder will continue to operate until the engine is stopped.

Risky parking mode

Use this mode when parking in areas with a high risk of theft. In this mode the system will require owner authorization with the factory buttons each time the system is disarmed.

This mode operates independently of the "Immobilizer mode" settings.

To enable/disable the mode, follow these steps:

  1. Disarm the alarm.
  2. Turn off the ignition.
  3. Press the service button twice.
  4. Turn on the ignition. Two audible signals will follow.

Enabling the mode will be confirmed by one audible signal and one visual signal, while disabling it will be confirmed by two audible and two visual signals.

Device Registration

To register new remote keys, tags, smartphones, use the "Device Registration" mode.

To prevent unauthorized registration of new accessories, entry to registration mode is permitted in Disarmed mode only. If Immobilizer mode enabled then authorization must be passed to fully disarm a system.

Tags and smartphones shall be registered in one registration cycle. All previously paired tags and smartphones will be deleted from memory if not paired again together with the new ones. A total of up to 5 devices can be registered in the system.

When registering new primary and additional remote keys, all previous remote keys will be removed from memory, and they must be registered again. A total of up to 4 remote keys can be registered in the system.

All steps of device registration must be completed without long pauses between them.

Entering the device registration mode

  1. Set the system to "Disarmed" mode.
    6.png
  2. Turn off the ignition (if it was on).
    7.png
  3. Press the service button 7 times.
    8.png
  4. Turn on the ignition. There will be 7 flashes of the service button LED and 7 audible signals.
    9.png
  5. Entry into the registration mode will be confirmed by 2 flashes of the service button LED and 2 audible signals.2.png

Registration of primary and additional remote keys

  1. Press buttons 1 and 2 of the remote key briefly.
    n_Кнопка 1 _Кнопка 2.png
  2. After 3 seconds, successful registration will be confirmed by a short sound signal from the remote key, 2 flashes of the service button or transceiver LED, and 2 sound signals. If the remote key is not registered, the remote key will emit 4 sound signals.
  3. Perform steps 1 and 2 for each remote key.

Registration of tags

  1. Remove the power element from the tag.
    12.png
  2. Press and hold the tag button and insert the power element. The LED of the tag will light up red.
    13.png
  3. Release the button and monitor the series of red flashes for 10 seconds.
    14.png
  4. Successful registration will be confirmed by a green flash, 2 flashes of the LED on the transceiver, and 2 sound signals. If the tag is not registered, the LED of the tag will remain red.
    n_Кнопка-трансивера-и-метка_2.png
  5. Repeat steps 1-3 for the remaining tags.

Registration of a smartphone:

  1. Enable Bluetooth in the smartphone settings.
  2. Select StarLine equipment from the list of available devices.
  3. Enter the code "000000" (on the iOS platform, press the "Pair" button to enter the code).

If multiple registered smartphones are simultaneously in the vicinity, the system will only work with the one that connects first.

Removing a smartphone from the memory of the security system

A previously recorded smartphone in the system's memory will be automatically removed after registering a new smartphone or tag.

Make sure to remove the system from the list of paired Bluetooth devices on your smartphone.

Exiting the device registration mode

Exiting the "Device Registration" mode is automatic after 5 minutes or when the ignition is turned off.

7.png

The exit will be confirmed by 2 flashes of the service button or transceiver LED and 2 sound signals, followed by signals corresponding to the total number of registered remote keys, BT tags, and smartphones.

Emergency disarming

Use the emergency disarmament code provided on the owner's plastic card or PIN envelope in the following situations:

PIN envelope

pinEnvelope.jpg

Entering emergency disarm code via the service button

To emergency disarm the system, follow these steps:

  1. Ensure that the ignition is off.
    7.png
  2. Press the service button a number of times corresponding to the first digit of the emergency disarm code.
    4_1.png         
  3. After 3 seconds, the digit entry will be confirmed by flashes of the service button LED. The number of flashes will correspond to the sequential number of the emergency disarm code digit (1, 2, 3, or 4 times).
  4. Repeat steps 1 and 2 for the remaining digits.

If the emergency disarmament code is entered correctly, the system will emit 3 short sound signals and 3 light signals, and transition to the "Disarmed" mode.

If the emergency disarmament code is entered incorrectly 3 times, the ability to re-enter the code will be blocked for 15 minutes.
An attempt to enter a digit will be indicated by 5 flashes of the service button LED.

Example of entering the code 5342 using the service button.

схема ввода кода экстренного выключения охраны _кнопка_.png

Entering emergency disarm code via the StarLine EC-1 Capacitive Sensor

The emergency disarm code can be entered using the StarLine EC-1 capacitive sensor (installed optionally).

To disarm the system, follow these steps:

  1. Touch the door handle 3 times. A single sound signal will follow.
  2. Touch the door handle a number of times corresponding to the first digit of the emergency disarmament code. The input will be confirmed by a flash of the service button LED.
  3. Enter the remaining digits of the code as in step 2. Flashes of the service button LED will follow. The number of flashes will correspond to the sequential number of the emergency disarmament code digit (1, 2, 3, or 4 times).
  4. If the emergency disarmament code is entered correctly, there will be 2 flashes of the service button LED and 2 sound signals. The system will transition to the "Disarmed" mode.

If the code is entered incorrectly, there will be 4 flashes of the service button LED and 4 sound signals.

If the emergency disarmament code is entered incorrectly 3 times, the ability to re-enter the code will be blocked for 15 minutes.
An attempt to enter a digit will be indicated by 5 flashes of the service button LED.

Changing the emergency disarm code

To change the code, you need to know the current emergency disarm code.

The initial emergency disarm code is indicated on the owner's plastic card or PIN envelope included in the delivery set.

PIN envelope

pinEnvelope.jpg

The emergency disarm code may contain any digits except zero.

Changing the emergency disarm code via the service button

To change the emergency disarmament code using the service button, you need to first enter the current code and then the new code twice:

  1. Put the system in the "Disarmed" mode.
  2. Press the service button 4 times.
  3. Turn on the ignition. Confirm the action by observing 4 flashes of the service button LED and 4 sound signals.
  4. The system's transition to the emergency disarm code change mode will be confirmed by 2 short flashes of the service button LED and 2 sound signals.

    If there is no activity within 5 seconds, the system will automatically exit the emergency disarm code change mode.

  5. Turn off the ignition.
  6. Turn on the ignition and press the service button a number of times corresponding to the first digit of the current emergency disarm code.
  7. Turn off the ignition. The service button LED will light up, and the number of flashes will correspond to the digit position of the emergency disarm code (1, 2, 3, or 4 times).
  8. Repeat steps 6...7 for the remaining code digits.
  9. There will be 2 flashes of the service button LED and 2 sound signals, confirming the correct entry of the current code.
  10. Turn on the ignition. Press the service button a number of times corresponding to the first digit of the new emergency disarm code.
  11. Turn off the ignition. The service button LED will light up, and the number of flashes will correspond to the digit position of the emergency disarm code (1, 2, 3, or 4 times).
  12. Repeat steps 10...11 for the remaining new code digits.
  13. There will be 2 flashes of the service button LED and 2 sound signals, confirming the acceptance of the new emergency disarm code.
  14. Enter the new code again by repeating steps 10...12.
  15. There will be 2 flashes of the service button LED and 2 sound signals, confirming the recording of the new emergency disarm code.
Example of changing the emergency disarm code using the service button

To change the current emergency disarm code from 7184 to the new one, 5463, follow these steps:

    1. Ensure that the system is in "Disarmed" mode.
    2. Press the service button 4 times.
    3. Turn on the ignition. The service button will flash 4 times, accompanied by 4 beep sounds.
    4. The system will confirm the transition to the emergency disarm code change mode with 2 short flashes of the service button LED and 2 beep sounds.
    5. Turn on the ignition.
    6. Press the service button 7 times. Turn off the ignition.
    7. The service button will flash once.
    8. Turn on the ignition.
    9. Press the service button once. Turn off the ignition.
    10. The service button will flash twice.
    11. Turn on the ignition.
    12. Press the service button 8 times. Turn off the ignition.
    13. The service button will flash three times.
    14. Turn on the ignition.
    15. Press the service button 4 times. Turn off the ignition.
    16. The service button will flash four times.
    17. Two short LED flashes and 2 beep sounds will confirm the correct entry of the current code.
    18. Turn on the ignition.
    19. Press the service button 5 times. Turn off the ignition.
    20. The service button will flash once.
    21. Turn on the ignition.
    22. Press the service button 4 times. Turn off the ignition.
    23. The service button will flash twice.
    24. Turn on the ignition.
    25. Press the service button 6 times. Turn off the ignition.
    26. The service button will flash three times.
    27. Press the service button 3 times. Turn off the ignition.
    28. The service button will flash four times.
    29. Two short LED flashes and 2 beep sounds will confirm the acceptance of the new emergency disarm code.
    30. Turn on the ignition.
    31. Press the service button 5 times. Turn off the ignition.
    32. The service button will flash once.
    33. Turn on the ignition.
    34. Press the service button 4 times. Turn off the ignition.
    35. The service button will flash twice.
    36. Turn on the ignition.
    37. Press the service button 6 times. Turn off the ignition.
    38. The service button will flash three times.
    39. Press the service button 3 times. Turn off the ignition.
    40. The service button will flash four times.
    41. Two short LED flashes and 2 beep sounds will confirm the recording of the new emergency disarm code.

Changing the owner authorization code

The owner authorization code is used to authenticate the user via the car's built-in buttons. To change the owner authorization code, follow these steps:

  1. Set the system to "Disarmed" mode.
    6.png
  2. Turn off the ignition if it is on.
    7.png
  3. Press the service button 7 times.
    8.png
  4. Turn on the ignition. The service button LED will flash 7 times, accompanied by 7 beep sounds.
    9.png
  5. The system will confirm entering the registration mode with 2 flashes of the service button LED and 2 beep sounds.
    2.png
  6. Enter the new owner authorization code using the car's built-in buttons with an interval of no more than 3 seconds between presses. Each press will be accompanied by a single flash of the service button LED.

    23.png


    The owner authorization code consists of a sequence containing from 2 to 25 presses of the car's built-in buttons. Refer to the list of supported car buttons on the can.starline.ru website. If there is no flash of the service button LED after pressing the car's built-in button, then the button is not supported in this car.


  7. Two flashes of the service button LED and 2 beep sounds will confirm the acceptance of the code 3 seconds after the completion of entering the owner's code.
    2.png
  8. Enter the owner authorization code again.
  9.  If the code is entered correctly, there will be 2 flashes of the service button LED and 2 beep sounds. If the code is entered incorrectly, there will be 4 flashes of the service button LED and 4 beep sounds. In this case, repeat steps 5 to 8.
  10. Turn off the ignition after 10 seconds to exit the registration mode.
    7.png
  11. Exiting the "Device Registration" mode will be confirmed by 2 flashes of the service button LED and 2 beep sounds, after which there will be signals corresponding to the total number of registered remote keys, BLE tags, and smartphones.

Deleting the owner authorization code

To delete the owner authorization code, follow these steps:

  1. Set the system to "Disarmed" mode.
    6.png
  2. Turn off the ignition if it is on.
    7.png
  3. Press the service button 7 times.
    8.png
  4. Turn on the ignition. The service button LED will flash 7 times, accompanied by 7 beep sounds.
    9.png
  5. Entering the registration mode will be confirmed by 2 flashes of the service button LED and 2 beep sounds.
    2.png
  6. Press the service button 3 times.
  7. Wait for the long signal of the service button LED, confirming the deletion of the code from the system memory.
  8. Turn off the ignition.
    7.png
  9. Exiting the "Device Registration" mode will be confirmed by 2 flashes of the service button LED and 2 beep sounds, after which there will be signals corresponding to the total number of registered remote keys, BLE tags, and smartphones.