StarLine B9v2, B9v3 User manual Safety precautions Attention! Read the manual prior to use security system and pay attention to the sections marked with . In order to check whether this security system is suitable for your car follow a vehicle instruction manual and manufacturer’s requirements. StarLine security system is a complicated technical appliance implying connection to vehicle wiring and equipment, including those related to engine operation. It must be installed by qualified and trained auto electronics technicians only, passed necessary training and examined on safety rules observing. The security system configured parameters shall not contradict a vehicle instruction manual requirements. User bears a full responsibility on any damage incurred to people, animals and assets as a result of inappropriate use of security system and violation safety precautions specified in this manual. Manufacturer shall not be responsible for any losses and injuries caused with breaching safety rules described herein. If your security system has a remote key or a wireless tag (transponder) follow below recommendations: Do not carry remote key or tag on the same bundle with a car original keys Always switch over the system to service mode when handing  a car over for maintenance or car wash. Do not give tags and remote keys to other persons in order to avoid unauthorized access to security functions Do not leave remote key or tags in children and animals reach Avoid any liquids ingress in remote key Replace battery in remote key once a battery drain warning icon appears on display Store a spare tag and/ or remote key battery in vehicle inside its factory packing Mandatory safety precautions while use of remote engine start functionality It should be borne in mind that a car is a source of extra hazard. Driver can leave a vehicle only ensured that vehicle cannot move spontaneously or by unauthorized persons. Study carefully the mandatory safety precautions for remote engine start option use: Always park a vehicle at open and well ventilated area. Always tighten a parking brake, which must be fully operable and insured of vehicle movement. Make sure of leaving vehicle with automatic transmission shifted to parking position and manual transmission shifted to neutral. On manual transmission version always execute “program neutral” procedure before leaving a vehicle to be able activate remote engine start then. Never give the security system remote key, tag or mobile phone with StarLine app over children or other persons unless operation manual carefully studied. Before remote engine start activation make sure of:      engine and entire vehicle are fully operable with no faults indicated on dashboard; sufficient level of fuel, oil, cooling and other technical fluids available; necessary parameters of climate control unit, heating and other accessories are preset; set fan regulator to an air circulation position for more effective cabin cooling or warming up. Safety precautions while vehicle storage battery charging Remember that any battery charging process implies supply of voltage exceeding the rated 12 V to the storage battery and accordingly to vehicle circuits, which may damage factory electronic and optional electronic equipment of vehicle. Do not use charging and starting-charging devices for storage battery charging directly on vehicle without disconnecting battery terminals from vehicle circuits in following modes: rapid charging by increased current («boost» or similar modes); various START modes intended for engine starting Never use starting and charging devices for engine starting with main battery disconnected or with inoperable main batteries connected (short circuits in banks, breakage of plates etc.) Never use faulty charging devices, 24V charging devices and other power supply equipment (i.e. welding inverters), not dedicated to charge 12V vehicle batteries. It is recommended do not use so named “light up” method for charging vehicle battery and start engine by connecting cables from a donor vehicle battery. Owner is fully responsible for possible short circuit or surge voltage and damaging of security system and vehicle electronic components caused while using this method.  Follow a safe storage battery charging procedure! Before charging a battery terminals shall be disconnected from vehicle circuits. Then battery charging can be started. After charging, connect battery terminals back to vehicle circuits. It is necessary due to impossibility of detection main battery charge and health state without specific measuring equipment (i.e. internal short circuits or plates breaks). Connecting a charging device to an inoperable storage battery may cause a risk of car electronic equipment and security system damage with over voltage.  General Description Security telematic system StarLine B9 (hereinafter the system) is intended for vehicle securing against theft, immobilising and convenient remote control via cellular networks and location monitoring with use of global satellite positioning systems. Depending on delivery set StarLine security system can be controlled with radio remote key, wireless radio tag (transponder), with voice calls, text messages and mobile app or at starline.online web monitoring service account. Use login and password from personal ID card to sing in starline.online account and app. Major benefits 2xSIM cards dual stand by operation supported; embedded buzzer for installer and owner notification; external microphone to listen vehicle interior remotely; «Slave» mode to arm and disarm security systems with use of factory key or Keyless-go; driver authentication by wireless tag, paired smartphone via Bluetooth Smart or by PIN code entered with factory buttons (Pin- to-Drive); Anti-hijack mode by a tag loss in trip or by remote command; short range radio control secured with Dialogue Code and 128 bit encryption keys, ensuring security against all existing code grabbers; embedded 2CAN+4LIN digital interface for easier integration with modern vehicles control circuits; control over vehicle statuses (battery voltage, faults, mileage, fuel level, distance to empty etc.) remote and automatic engine start by preset temperature, timer, battery charge level; factory immobilizer bypass with external immobilizer bypass module or with embedded data immobilizer bypass via CAN, LIN interfaces; remote control over parking heaters and auxiliary heaters; vehicle location monitoring, routes logs, drive style scoring (with use of optional GPS+GLONASS receiver); data recording and storage a trip data in non-volatile memory (“black box”); universal programmable input and output channels; Flexible Logic for customized system operation in various individual scenarios; universal StarLine Master installer’s software for system configuration and updating. Technical Specifications Parameter Values Short range control 2.4GHz Bluetooth Low Energy Middle range radio control range 868 MHz Rated radio control distance up to 1500 m Rated radio notification distance up to 2000 m Cellular networks range 2G version: 2G GPRS 850, 900, 1800, 1900 4G version: 2G GPRS 900, 1800 3G WCDMA B1 (2100), B8 (900) 4G LTE B1 (2100), B3 (1800), B7 (2600), B8 (900), B20 (800) Antenna type Embedded SIM cards 2 x nanoSIM GPS+GLONASS receiver sensitivity –148 dBm —«cold start» –163 dBm —«hot start» –165 dBm — in active monitoring Interfaces • 2xCAN or 3xCAN-FD • 4 x LIN • 1 x StarLine coded data bus • 1 x USB • 18 programmable channels which can be set as: • 15 OC negative outputs – 200 mA max • 2 positive outputs – 2 А max • 3 positive inputs • 3 negative inputs • 1 universal input • external temperature sensor input • external service (valet) button input • external microphone sensor input Input voltage 8 – 16 V Rated current 10 – 15 mA Tag battery CR2032 3V Remote key battery LR03 AAA 1.5V Operating temperature range −40 °С ... +85 °С Main unit dimensions 105 х 63 х 16 mm Main unit weight 63 g Personal ID Personal ID card Delivery set includes an owner personal ID card containing following data: Login and password for StarLine personal account at starline.online or StarLine app Emergency disarm code for instant security deactivation when regular disarming methods unavailable Service code to enter main unit configuration parameters in StarLine Master software Main unit serial number Remove protection layer from plastic card carefully. Do not use metal and other sharp items to avoid occasional erasing a printed information under layer. Do not tell emergency disarm code and StarLine account details to anybody! Due to security reasons a personal information from ID card is generated randomly at factory, never stored in any database and therefore cannot be recovered once it is lost! A system main unit with lost Service code and Emergency disarm code cannot be normally used and must be replaced to a new one. Recommend to copy and store ID card information in a safe place in reach. StarLine.online service and mobile app StarLine system can be remotely controlled and monitored with use of starline.online web monitoring platform and StarLine mobile app with free of charge unlimited subscription. Make sure that a proper local SIM card with active balance and permission to operate with M2M smart devices is installed and configured at installation. Correct APN details for internet access, SMS center number and time zone must be set in system configuration. SIM card boot PIN code must be disabled prior to inserting into the main unit. Check out if the cellular standards and bands supported by the built-in modem in corresponding hardware version conform to your local operator bands. Enter Login and Password from personal ID card to sign in starline.online personal web account or StarLine 2 mobile app (available on Android and iOS platforms). All StarLine systems have a preregistered account at starline.online and mobile App. Do not forget to enter and verify your email in personal StarLine account. Verified email is necessary to restore forgotten password, access sharing and other important functionality. If your system has been removed from the factory registered account for any reason (occasionally or by a previous owner), then a new StarLine personal account can be registered                                                               Control via Bluetooth When cellular network is not available or SIM card balance is inactive, then StarLine system can be controlled with StarLine App via Bluetooth on a short distance from vehicle (up to 50 m approx). Supported for smartphones with Bluetooth Low Energy 4.2 version and above. To use Bluetooth communication make smartphone pairing in Accessories registration mode. Then enable connection with paired device in StarLine 2 app Bluetooth settings. Lights and sound indication Security system indicates its status by means of sounds (siren or buzzer) and lights (hazard or other lights) — short signal; — long signal. Events Lights Sounds Arming Arming with one of secured zones breach Arming with Hands free mode disabling Arming with Hands free mode disabling and one of secured zones breach Disarming Disarming (one of secured zones breached in armed mode)       Disarming with Hands free mode disabling — Alarm 30 sec 30 sec Warn away alarm Panic 10 sec 10 sec Trunk unlock Anti-Hijack mode off -  LED service button indication State of security system LED light Disarmed Off Disarmed with ignition On and one of secured zones breach (doors, hood, trunk) 1 flash per 5 sec Armed 1 flash per 1 sec Armed with Hands free mode active 2 flashes per 1 sec Engine is running Continuous On Service (valet) mode Off Immobilizer mode active Off Anti-Hijack mode active 10 times per 1 second Invalid emergency disarm code entered 4 flashes Emergency disarm code entry blocked for 15 min 5 flashes Valid emergency disarm code entered 2 flashes Embedded buzzer sound indication Events Sounds Waiting for authorization 10 sec Tag battery discharged (at ignition On) Valid authorization PIN code entered Invalid authorization PIN code entered Control with wireless tag (transponder) (optional accessory) Wireless tags availability depends on delivery set. The included and optional tags are supplied from factory in transport (power saving) mode, i.e. inactive! Pushing a tag button in this mode is indicated by green and red alternating flashes of the built-in LED. To switch it to normal mode push a tag button several times until flashing color turns to green. Connection check Push button once to check tag connection status. 2 LED flashes means connection with security main unit established, 1 flash means disconnected. A flash color corresponds to the current active mode: green–Regular mode, Anti-hijack is disabled  red–Anti-hijack mode is enabled yellow–Service mode is enabled Control over security system Duration of a tag button pushing: short – push and release button, followed with a flash of corresponding current operation mode; long–push and hold button until LED begins flashing. Duration of long push are of 2 levels: 1 level – push and hold button followed with double short flashes of a current operating mode and then long flash at which button must be released; 2 level – push and hold the tag button followed with double short flashes of a current operating mode, then one long flash  and then followed with serial flashes at which button must be released. Command Button push Arm/Disarm 1 short Enable / disable Anti-hijack by a tag away long 1 level Enable/Disable Service mode long 2 level Replacing a tag battery Wireless tag (transponder) is equipped with CR2032 type Li-ion battery. Tag battery discharging is indicated with 3 sounds of embedded main unit buzzer (or siren) at ignition On and owner is notified with text message to his phone number. Then battery must be replaced as soon as possible. To replace battery open a tag casing carefully with a flat metal or plastic item, remove discharged battery from slot. Install a new battery in the slot observing correct polarity (positive side up, as shown on picture). Then fix a cover back. Tag is ready for operation.   A smartphone with support of Bluetooth 4.2 and above can also be used as a tag. See Devices registration article to pair a smartphone as a tag. Control with 2-way remote key (optional accessory) LCD remote control and matching external RF868 transceiver are optional accessories and can be ordered from local dealer. Display icons meaning Remote engine start Icons Meaning Engine is running Automatic engine start by timer enabled Periodic automatic engine start enabled Automatic engine start by temperature enabled Automatic engine start by battery voltage drop enabled Program neutral executed Parking heater activated (blinking) Operating Modes Icons Meaning Armed Hands-Free mode Service mode Programming mode Buttons lock Anti-hijack mode Secured zones Icons Meaning Ignition switched On Parking brake tighten Hood open Door open Trunk open Sensors Icons Meaning Motion or tilt sensors triggered Auxiliary sensor 1 triggered Auxiliary sensor 2 triggered Tilt sensor triggered Motion sensor triggered Shock sensor warning level triggered Alarm level of shock sensor triggered Shock sensor disabled Additional indicators Icons Meaning Data transfer Replace remote battery Siren sounds enabled Siren sounds disabled Control commands Definition of buttons push duration Short Push Pushing one or two buttons once less than 1,5 sec. Example:   — first button short push; — short push of first and second buttons simultaneously. Long Press Pushing and holding a button or two buttons until melody and vibration come up. 2 levels of a long pushing are envisaged: • 1 level long push – push and hold until a first melody.  Example:  — 1 button long push; — 1 and 2 buttons long push simultaneously; 2 level long push — push and hold until a second melody; Example:  — 4 button long push of a 2 level. Double push Double push of one button within 1 sec. Example: — double push of 1 button. Triple push Triple push of one button within 1 sec. Example: — triple push of 1 button. Sequential push Double push of one or two buttons with different duration. First pushing is long (1 or 2 level) and second push is short. Firs button must be released before pushing next button. Example: — sequential pushing 2 and 1 buttons. Control commands Commands Button combinations Arm Silent arming Disarm Silent disarming Request vehicle statuses (engine and cabin temperature, battery voltage, fuel level). At remote start – remaining engine run time. Start engine Stop engine Start parking heater Stop parking heater Find car on parking Switch shock sensor On / Off Switch motion / tilt sensor On / Off Enable Panic Unlock trunk Enable automatic engine start configuration menu Enable / disable Service mode or configuration menu Enable / disable Hands free mode configuration menu Enable/disable buttons lock Enable/disable auto buttons lock Enable vibration only Enable sound profile 2  Enable sound profile 1 Enable sound profile 0 Enable sound profile -- Activate Flexible Logic program Modes menu Some options and operation modes are controlled in Modes menu: Hands Free mode, Service mode, Autostart settings. Modes menu is entered and exited with 4 button long push level 1: . Modes menu is automatically exited when no any buttons pushed 15 sec.  Modes submenu is flipped with or buttons short push forward and backward accordingly. Submenu options are selected with 2 and 3 buttons short push:  .   Parameters are tuned with and  buttons short push up and down accordingly. Long buttons pushing increases parameters tuning speed. Listing menu points, changing settings and menu exit are confirmed with melody.   Icons Parameters Description Tune step Hands Free mode Enable / disable Hands Free mode — Automatic engine and parking heater start by timer Set engine start hour and min. Engine and parking heater autostart settings are switched with short pushing buttons  and . Engine start settings are indicated with digit 1, parking heater settings – with digit 2. 1 min Periodic engine start Set engine start interval in hours 1 hour Automatic engine start by temperature Set engine start temperature in Celsius degrees 1 ºС Automatic engine start by battery voltage Set main storage battery voltage limit in Volts 0,1 V Service mode Enable / disable service mode — Settings Menu Operation parameters are set in the Setting menu. Settings menu is entered and exited with 4 button long push level 2:  .  1 — parameter function number 2 — parameter value Operation menu points are flipped with and  buttons up and down accordingly. Parameters are tuned with and buttons short push up and down accordingly. Long buttons pushing increases parameters tuning speed. Listing menu points, changing settings and menu exit are confirmed with melody. Time zone setup Select 1 item of Settings menu and set matching time zone with   and     buttons. Current time is automatically retrieved from cellular network and satellites data (if GPS module is available).   Setting lights and siren indication at Arming and Disarming Select 2 item of Settings menu and set the mode with and   buttons: 0 – hidden mode without siren and lights indication 1 – silent mode with lights indication only 2 – full mode with siren and lights indication                                                                                                                                          3 – only siren indication Setting siren volume at Arming and Disarming Select 3 item of Settings menu and set siren volume level with and buttons: 0 — silent mode, 10 — max volume  Setting lights and siren indication in Alarm mode Select 4 item of Settings menu and set the mode with and buttons: 0 – hidden mode without lights and siren indication 1 – silent mode with lights indication only 2 – full mode with lights and siren indication Setting siren volume setup in Alarm mode   Select 5 item of Settings menu and set siren volume level with  and buttons: 0 — silent mode, 10 — max volume Setting motion sensor sensitivity Select 6 item of Settings menu and set sensor sensitivity from 0 to 30 level with  and buttons: 0 - motion sensor is disabled, 30 – max sensitivity Setting tilt sensor sensitivity Select 7 item of Settings menu and set sensor sensitivity from 0 to 30 level with and buttons: 0 – tilt sensor is disabled, 30 – max sensitivity Setting shock sensor warning level sensitivity Select 8 item of Settings menu and set sensor sensitivity from 0 to 30 level with  and buttons: 0 – warning level shock sensor is disabled, 30 – max sensitivity The warning shock sensor sensitivity must be set over the main shock sensor level. Setting shock sensor main alarm level sensitivity Select 9 item of Settings menu and set sensor sensitivity from 0 to 30 level with and buttons: 0 – main alarm shock sensor is disabled, 30 – max sensitivity The main alarm shock sensor sensitivity must be set below the warning shock sensor level. Setting tag (transponder) loss range Select 10 item of Settings menu and set tag loss range value from 3 to 10 level with  and buttons: 3 – min distance, 10 – max distance Setting tag (transponder) detection range Select 11 item of Settings menu and set tag detection range value from 1 to 8 level with  and buttons: 1 – min distance, 8 – max distance Tag detection range must be set less than a tag loss range.   Setting remote key connection control Select 12 item of Settings menu and set connection control period to 1 or 2 value with and buttons: 0 – connection control is disabled, 1 – connection check every 3 min Setting turbotimer run time Select 13 item of Settings menu and set turbotimer run time from 1 to 5 min with and buttons. Remote engine start must be enabled in system configuration parameters for this option.   Setting remote / automatic engine start duration Select 14 item of Settings menu and set engine run time from 10 to 60 min with and buttons.  Settings max duration of extended remote / automatic engine start Select 15 item of Settings menu and set extended engine run time from 15 to 60 min with  and buttons.  Setting parking heater starting max duration Select 16 item of Settings menu and set max parking heater starting interval from 1 to 10 min with and buttons. Setting parking heater run time duration Select 17 item of Settings menu and set parking heater run time from 5 to 60 min with   and buttons. Setting parking heater activation before remote engine start Select 18 item of Settings menu and set parking heater activation before remote engine start with and buttons: 0 – do not start parking heater 1 - start parking heater before remote engine start Setting parking heater activation before automatic engine start Select 19 item of Settings menu and set parking heater activation before automatic engine start with and buttons: 0 – do not start parking 1 - start parking heater before automatic engine start Settings temperature for parking heater activation before remote and automatic engine start Select 20 item of Settings menu and set parking heater activation temperature before remote and automatic engine start from –5 to –30 ºС with and buttons. Setting temperature for automatic engine start Select 21 item of Settings menu and set automatic engine start temperature from +10 to –40 ºС with and buttons. Setting 2 way remote key detection range Select 22 item of Settings menu and set remote key detection range from 1 to 10 level with and buttons: 1 – min distance, 10 – max distance. Sound profile menu Sound profiles menu contains settings for commands confirmation, alarm trigger and buttons pushing. Profiles are selected with following buttons combination: № Profile  Button combination Description (at default settings) 1 SOUND 2 All signals at max level and vibration enabled. 2 SOUND 1 All signals at min level and vibration enabled. 3 SOUND 0 Vibration only, all sounds Off 4 SOUND - Fully silent, vibration and all sounds Off Changing sound profile settings Sound profile menu is entered with long pushing level 2. Setting commands confirmation signals   1 — selected signal type volume level 2 — selected sound profile number  3 — commands confirmation sound settings icon 4 — vibration:  — enabled,  — disabled Sounds volume is tuned with and buttons short push. Vibration is enabled and disabled with button short push. Next sound signal type is flipped with  button short push. Setting alarm sounds volume 1 — Selected signal type volume level; 2 — Selected sound profile number; 3 — Vibration:  — enabled, — disabled; 4 — Alarm sounds volume settings icon. Sounds volume is tuned with or  buttons short push. Vibration is enabled and disabled with  button short push. Next sound signal type is flipped with button short push. Setting buttons push sound volume 1 — buttons sound volume setting icon 2 — selected volume 3 — selected sound profile 4 — vibration:  - enebled,  - disaabled Sounds volume is tuned with or  buttons short push.  Vibration is enabled and disabled with button short push.  Next sound signal type is flipped with button short push.  Sound profile settings menu is automatically exited in 10 sec if no any buttons pushed. After exit the set sound profile is indicated for several sec. Resetting sound profile to factory default settings Select the necessary sound profile with corresponding buttons combination. Enter sounds profile menu with long pushing level 2. Hold 3 button until next sound signal . Setting sounds tone The sounds tone can be also setup in sounds profile menu. Enter to sounds profile menu with long pushing level 2. Push buttons  shortly. The current sounds tone St-1 or St-2 shall be displayed. St-1 tone is set as default. Push buttons    shortly to select next tone.  Sounds tone menu is automatically exited in 10 sec if no any buttons pushed.   Buttons auto lock The option locks buttons automatically each time after backlit off. It is enabled and disabled with long push  level 2. Remote key searching Push and hold service (valet) button for 5 sec – remote key shall beep.   Operation modes Security modes Armed Disarmed Anti-hijack Alarm Panic Supplementary modes «Slave» Hands Free Service mode Registration Configuration Armed Mode Install external short range radio transceiver to control alarm system with two-way key fob. The following zones are controlled in armed mode: ignition, doors, trunk, hood, shock sensor, tilt sensor, motion sensor, auxiliary sensor. If any zone is breached then system shall trigger alarm. System can be armed when ignition off only. If arming command received at ignition on, then only doors are locked. System is armed in one of following ways: Pushing tag button once shortly in disarmed mode Pushing remote key button shortly SMS text command  11 ; Voice call menu command  11   ; Command from StarLine mobile app; Command from  starline.online web account; Arming with factory security system in "Slave"; When the tag is lost or the door handle sensor is touched in "Hands-Free" mode Tag loss or holding capacitive sensor in Hands Free mode  System shall confirm arming with 1 lights flash and 1 siren sound. If any of doors, hood, trunk are still open then system shall warn thereof by 4 siren sounds and 4 lights flashes. Shut the breached zone and make sure that 1 light and sound of arming confirmation followed. Silent arming System can be armed silently without siren sound confirmation in following ways: Triple pushing  remote key button   SMS text command  111 ; Voice call menu command  111 ; Command from StarLine mobile app; Command from starline.online web account. Silent arming is confirmed with 1 lights flash. Emergency arming In case of a tag, remote key batteries discharged and other methods of arming via app and starline.online not available, then system can be armed with following way: Push service button or external transceiver button 3 times. Switch ignition On 3 beeps will follow. Make sure next 2 beeps come up. Switch ignition Off. Leave vehicle and shut the doors. Disarmed mode System is disarmed by one of following ways: Short push of remote key button pushing tag button once shortly in armed or alarm mode SMS text command  10  Voice call menu command  10   Command from StarLine mobile app Command from starline.online web account Disarming factory security system (Slave) Tag detection or touching capacitive sensor in Hands Free mode Disarming is confirmed with 2 siren sounds and 2 lights flashed. If alarm was triggered while armed mode then 3 siren sounds and 3 lights flashes come up at disarming. All events happened in armed mode will be indicated on remote key display after disarming. If no any actions taken after disarming (i.e. doors, trunk were not open), then system shall automatically turn to armed mode back and lock the doors (Re-arming). Silent Disarming System can be disarmed silently without siren sound confirmation in following ways: Triple pushing remote key button   SMS text command  101  Voice call menu command  101   Command from StarLine mobile app Command from starline.online web account Silent disarming is confirmed with 2 lights flash. If alarm was triggering while armed mode then 3 lights shall follow at silent disarming. Automatic doors locking on a trip System can make automatic doors locking on a trip at one of following selected terms: ignition is switched On vehicle starts moving and brake pedal pressed parking brake released automatic transmission is shifted from parking position  preset vehicle speed is reached Automatic doors unlocking on a trip System can make automatic doors unlocking on a trip at one of following selected terms: ignition is switched Off automatic transmission is shifted to parking position engine is stopped ignition is switched Off and automatic transmission is shifted to parking positioning parking brake is tighten Automatic doors lock / unlock option can be enabled and configured in StarLine mobile app or starline.online account. Trunk unlock in armed mode If this option is enabled in system configuration then owner can unlock and open trunk by means of a factory remote / trunk lid button in armed mode once StarLine tag is visible in detection range. Blocking factory Keyless-Go system The option of factory Keyless-Go blocking via CAN bus brings higher level security as it secures against factory key stealing and relay attack with specific radio hacking devices. The system shall lock factory Keyless-Go system once StarLine tag is away of detection range. And then unlocks it once tag is detected again in range. This option is disabled in default settings and must be enabled in system configuration. Owner authorization with tag must be enabled for this option operation. Find out if the option is supported for your vehicle via CAN bus at can.starline.ru Alarm Mode Alarm shall trigger when any of secured zones is breached in armed mode. System activates siren alert sound, hazards lights flashing for 30 seconds and notifies owner with phone call and text message. If breached zone is not restored system repeats alert cycle once again. Any warning zone breaching is followed with 3 lights flashes and 3 siren sounds. Alarm mode can be aborted with short push of a tag button and or remote key buttons. The maximum number of zone triggering is limited to 8 times within 1 security cycle. Panic mode Panic mode ensures owner and vehicle security and informs on intrusion attempt. This mode can also be used to easily locate vehicle in a parking lot. Mode can be activated with double pushing remote key button, with text message  19 or a command from StarLine mobile app. System shall activate siren alert and hazard lights flashing for 10 sec in order to scare an intruder and attract other people attention. Anti-hijack mode Anti-hijack mode secures driver against assault attempts in trip. The mode is activated either by owner command or by a tag loss in trip. Anti-hijack by owner command is activated by one of following ways: SMS text message  31   Voice call menu command  31   Command from StarLine mobile app Command from starline.online personal account System enables warning sounds and lights on upcoming engine blocking for 10 seconds. Then by reaching a speed below 30 km/h engine will be safely stopped. Exit from Anti-hijack mode is done by one of following ways: SMS text command  30 XXXX , where XXXX - emergency disarm code from ID card entering emergency disarm code with service button or external transceiver button at starline.online personal account with entering emergency disarm code In case of invalid emergency disarm code is entered 3 times, then a code entry will be blocked for 15 min and owner will be informed with text message. Anti-hijack by a tag or remote key loss in trip The mode can be activated by a tag button long push level 1, if it is enabled in system configuration settings. The mode operation algorithm depends on a vehicle speed reading from CAN bus.  Anti-hijack operation sequence when speed supported from CAN bus: any of secured zones has been breached (doors, hood or trunk) motions sensor has triggered in 30 sec system begins seeking for a tag or remote key in another 30 sec, if a tag or remote key has not been detected, system enables warning sound and lights for 10 sec by reaching a speed below 30km/h engine will be safely stopped.     2. Anti-hijack operation sequence when speed from CAN bus is not supported: any of secured zones has been breached(doors, hood or trunk) motions sensor has triggered in 30 sec system begins seeking for a tag or remote key in another 30 sec, if a tag or remote key has not been detected, system enables warning sound and lights for 10 sec engine will be stopped in 3 min or at brake pedal pressing. Exit from Anti-hijack mode by a tag or remote key loss is made by one of following ways: When tag or remote key is detected in range SMS text command  30 XXXX , where XXXX - emergency disarm code from ID card entering emergency disarm code with service button or external transceiver button at starline.online personal account with entering emergency disarm code In case of invalid emergency disarm code is entered 3 times, then a code entry will be blocked for 15 min and owner will be informed with text message. By default,  Anti-hijack mode when the tag or remote key is lost is turned off. To turn it on, press and hold the button on the tag until you see a long red flash, then release the button. Slave mode Slave mode allows to control security system by means of a factory remote control or Keyless-Go system. System detects unlocking doors and disarming factory security and waits for owner authorization with any of below methods before disarming itself: Waiting for authorization starts at any of door, hood and trunk open. Tag or remote key detection in range at disarming during adjusted interval from 15 to 60 sec Entering personal PIN code with factory buttons at ignition On during adjusted interval from 15 to 60 sec If authorization failed by any of methods then system shall activate warning siren sounds and then turn to alarm mode. It is highly recommended to enable above mentioned secondary owner authorization methods in Slave mode in system configuration settings. Hands Free mode Hands free mode allows automatic system arming and disarming by a tag loss and detection in range. The mode is enabled and disabled by one of following ways: SMS text commands  71   or  70 , accordingly Voice call commands  71   or  70 , accordingly From StarLine mobile app At starline.online personal account in remote key operation modes menu In this mode system is armed either by a tag loss from range or with holding door sensor (optional accessory) with a tag in range. Systems is disarmed by a tag detection in range or with touching door sensor (optional accessory) with a tag in range. If any of door, hood or trunk left open when tag is away, then system shall inform owner with SMS text message and siren alert on arming abort. Once a breached zone restored, system shall turn armed. If tag is lost on a trip (i.e. battery critically discharged) then system shall turn armed mode in 10 sec after any door open (auto arming). Auto arming is not executed in Hands Free mode when tag is in range. Disabling Hands Free mode for 1 security cycle When tag is within detection range at a parking place, then it is recommended to disable arming and disarming in Hands Free mode for 1 security cycle. Hands Free is enabled / disabled for 1 cycle by one of following ways depending on current state (disarmed / armed) accordingly: arming/disarming with a tag button accordingly arming/disarming with remote key button 1 and 2 System shall confirm successful disabling Hands Free for once cycle with 1 sound. System shall return to default Hands Free by following ways depending on current state (disarmed / armed) accordingly: • disarming and any of door, hood or trunk open • switching ignition On or arming command received Service (Valet) mode Service mode is used for temporary security deactivation and restricting access to system configuration while vehicle maintenance, car wash etc. Service mode can be activated from disarmed state only. In service mode following features are disabled: Arming and disarming Hands Free mode Doors lock and unlock in trip Remote and automatic engine start Turbotimer Trunk unlock Arming with open trunk with factory remote Panic Anti-hijack by a tag or remote key loss Entry to system configuration settings Entry to registration mode Service mode is enabled by any of following ways: Tag button long push level 1 (if this option is enabled in system configuration) Short push of  remote key buttons SMS text command   51   Voice call menu command  51  Command from StarLine mobile app Command from starline.online account In remote key operation modes menu Service mode activation is confirmed with a tag LED light turned yellow. Service mode is disabled by one of following ways: Tag button long push level 1 (if this option is enabled in system configuration) Short push of  remote key buttons SMS text command   50   Voice call menu command  50  Command from StarLine mobile app Command from starline.online account In remote key operation modes menu Emergency disarm code entry Automatic Exit from Service Mode If this option is enabled in system configuration then system automatically turns from Service mode to Waiting for authorization at configured event and ignition On. If authorization successfully passed then system turns to Disarmed. If authorization failed then system triggers Alarm and activates engine blocking. This option requires owner authorization, embedded sensors and vehicle speed from CAN bus to be enabled in system configuration. Immobilizer mode Immobilizer mode prohibits unauthorized drive attempt. Depending on settings system waits for owner authorization with a tag or remote in detection range or PIN code entered with factory buttons after every disarming or every ignition switching Off and at next ignition switching On. PIN code can be entered with factory buttons only when ignition is switched On. If authorization is not passed within 1 min, then engine will be stopped at a drive attempt for 1 min or until successful authorization passed. Remote engine start The feature allows to make remote and automatic engine start and stop to warm up or cool down vehicle interior to a comfortable temperature and warm up engine before a trip. Preparation of a vehicle with manual transmission for remote and automatic engine start. If vehicle is equipped with manual transmission , then system must be set to “Program neutral” state to prepare for further safe remote or automatic engine start in following procedure: • Tighten parking brake at engine running • Remove key from ignition barrel, engine continues running, service button LED will light up permanently • Leave vehicle, shut doors, hood, trunk and arm security system. Engine will be stopped. • System turns to Armed • “N” (program neutral) icon is indicated on remote key display and StarLine app main screen • System and vehicle are now ready for remote and automatic engine start. If any door is open or ignition is switched On after setting to Program neutral, then remote and automatic engine start will be denied until Program neutral procedure is executed again. Vehicle equipped with automatic transmission must be switched to Parking position in order to prepare it for remote or automatic engine start. Engine start Remote engine start can be activated by one of following ways: 3 x Lock command from factory remote control (if supported for particular vehicle model and enabled in system configuration SMS text command  21  Voice call menu command  21  Command from StarLine mobile app Command from starline.online personal account Automatic engine start can be activated by following terms: Engine or interior temperature Main vehicle battery voltage drop Periodic engine start set in hours Engine start by timer Parameters for automatic engine start can be configured in: Remote key operation modes menu StarLine mobile app starline.online account Automatic engine start is allowed only in armed mode, in 5 min after last engine stop and 1 hour after previous remote and automatic engine start. Engine stop Engine will be stopped when: Tag button short push once(if enabled in system configuration) Long push level 1 of remote key button SMS text command  20  Voice call menu command  20  Command from StarLine mobile app Command from  starline.online personal account Alarm mode triggered Vehicle motion detected Hood opened Parking brake released (for manual transmission) Automatic transmission is shifted out of parking position Brake pedal pressed Max engine temperature limit reached Drive after remote start without engine stop (ignition takeover) To start driving after remote / automatic engine start without engine stop make following depending on engine control system: for vehicles with ignition barrel disarm security system insert key into ignition barrel and turn it to ignition On start driving for vehicles with PTS (push-to-start) button Option 1: disarm security system press and hold brake pedal for 3 sec   Option 2: disarm security system push PTS button 1 or 2 times   Learn ignition takeover support and particular procedure from your StarLine installer. Parking heater (preheater) control This feature lets warm up engine and/ or interior before a trip with remote and automatic activating parking heater and auxiliary heater. Parking heater can be started manually in following ways: Sequentially pushing remote key buttons SMS text command  221  Command from StarLine mobile app Command from starline.online personal account Default parking heater run time at manual activation is 20 min and can be adjusted in system configuration. Factory and optional parking heater may have embedded primary factory settings, differ from those configured in system settings. Parking heater run time can be extended with sending repeated activation command. Parking heater can be stopped manually in following ways: Sequentially pushing remote key buttons SMS text command 220  Command from StarLine mobile app Command from starline.online personal account Parking heater can be automatically started before remote and automatic engine start on events and terms set in system configuration. Parking heater can be started automatically in following terms: by engine temperature – parking heater is started when engine temperature is below the set value by timer – parking heater is started at a set time  Temperature and time for parking heater activation can be set in: Remote key operation modes menu StarLine mobile app starline.online personal account Parking heater is stopped when the set engine start temperature (for automatic engine start) or the set parking heater run time is reached and engine will be started then. Default parking heater automatic run time is 20 min. It can be extended by sending heater start command again. Intelligent turbotimer Turbotimer option is used to temporary continue engine running after a trip to cool down turbo charger and extend its lifetime. The option must be initially enabled and programmed while installation. Turbotimer activation on vehicles with ignition barrel: Tighten parking brake at engine running. The service button LED shall light up permanently Take a key out of ignition barrel. Engine shall keep on running Leave a vehicle, shut doors, trunk, hood and arm security system Engine shall stop after interval sufficient for cooling down a turbine Turbotimer activation on vehicles with Push-to-Start button: Tighten parking brake at engine running Leave a vehicle, shut doors, trunk, hood and arm security system Engine shall stop after interval sufficient for cooling down a turbine Turbine cool down interval is calculated automatically and depends on engine speed before a trip finished. Max turbine cool down interval is 5 min. Beach mode In Beach mode system is armed and disarmed without a tag and remote key, which can be left inside vehicle. System is disarmed by owner authorization with emergency disarm code entered by means of StarLine EC-1 touch sensor installed in a door handle or another convenient place (under plastic parts). System does not execute any commands from remote key in this mode. Beach mode activation procedure: Disarm security system and switch ignition Off. Push service button or external transceiver button 3 times and switch ignition On. 3 sounds confirming entry to Beach mode shall follow. Switch ignition Off. Leave vehicle and touch door handle sensor 3 times. System shall turn armed. Hands Free mode is switched Off in Beach Mode until disarming.  Disarming (exit from Beach mode) is done by entering emergency disarm code be means of touch sensor with less than 3 sec intervals. Every valid digit entry is confirmed with sounds and flashes in corresponding number. Full valid code entry is confirmed with double sounds and flashes. If invalid emergency disarm code is entered 3 times, then next code entry will be blocked for 15 min. If nothing is done after disarming with emergency disarm code, then system shall return to armed and Beach mode remains active. Video recorder (dashcam) control The option must be initially wired and programmed while installation. System can automatically switch dashcam On to begin recording: at ignition switched On – dashcam is activated for 5min; at full alarm or warn alarm triggered – dashcam is activated for 2 min; with SMS command  69  dashcam is activated for 5min.      If engine is still running in armed mode then dashcam continues operating until engine is stopped. Risky parking This mode can be used in places with high probability of theft and robbery. In Risky parking mode system shall require owner authorization with factory buttons at every switching ignition On in disarmed mode. This mode operates regardless immobilizer mode settings made in system configuration. Risky parking activation: Disarm security system Switch ignition Off Push service button or external transceiver button twice Switch ignition On. Double sounds shall follow. Risky parking activation is confirmed with 1 sound and flash, deactivation – with double sounds and flashes. Cellular control commands System can be controlled with voice and SMS text commands from the owner master phone number (M1) and additional registered numbers (M2, M3, M4). The first incoming call telephone number shall be automatically recorded as M1 master number. All commands received from M1 number are executed without a GSM PIN code in default configuration. PIN code is recorded by owner at initial call from M1 number. Commands from M2...M4 numbers are executed with PIN code in the beginning, i.e. system arming command: 1234 11; where 1234 – PIN code, 11 – arming command number. Voice call commands Command Function М1  М2, М3, М4 Guest phones   0  Listen commands menu   10  Disarming   101  Silent disarming   11  Arming   111  Silent arming   12  Arming with shock sensors disabled   13  Arming with auxuliary sensor disabled   14  Arming with shock sensor warning level disabled   15  Arming with tilt sensor disabled   20  Remote engine stop   21  Remote engine start   31  Activate Anti-hijack mode   40  Request location   41  Request vehicle state   50  Disable Service mode   51  Enable service mode   70  Disable Hands Free   71  Enable Hands Free SMS text commands Text commands Function М1 М2, М3, М4 Guest phones   10  Disarming  ARM-   О-    101  Silent disarming   11   Arming  ARM+   О+    111  Silent arming   12  Arming with shock sensors disabled   13   Arming with auxuliary sensor disabled   14  Arming with shock sensor warning level disabled   15  Arming with tilt sensor disabled   19  Panic activation   PANIC    20  Remote engine stop  ENG-    21  Remote engine start  ENG+    220  Stop parking heater   221  Start parking heater   40  Request location   GPS    41  Request vehicle state   AUTO    45  Request cell connection status and SIM card balance   BALANCE   30 ХХХХ  Emergency disarming, where  XXXX    - emergency disarm code from personal ID card  A- ХХХХ    31  Activate Anti-hijack mode  А+    50  Disable Service mode  S-    51  Enable Service mode  S+    69  Activate video recorder (dashcam)   VIDEOREG    70  Disable Hands Free  R-    71  Enable Hands Free  R+   VALIDATOR-  Reset PIN-to-Drive code by factory buttons  8N  Activate FlexibleLogic program, where N – program number    SETTING+  Enter configuration via BLE  SETTING-  Exit configuration via BLE  FWUPDATE VER LANG  Firmware update via internet, where VER – firmware version number (can be written without dots, optional parameter); LANG — firmware language version (optional parameter): RU / EN / DE, ES / IT. If no any parameter added, then the latest release version and same language firmware is uploaded.  FWUPDATE STOP  Stop firmware update via internet  FWUPDATE?  Request status of firmware updating via internet  MAYAK+  Enable periodic connection mode (Beacon mode)  MAYAK-  Disable periodic connection mode (Beacon mode) Info commands Text commands Function М1 М2, М3, М4 Guest phone   05  Request registered accessories list  REG?    06  Request current GSM PIN code  GSMPSW?    07  Request registered master phone numbers   TEL    PHONES    09   Request GSM signal strength, battery voltage, firmware version status   INFO  GSM settings commands Text commands Function М1 М2, М3, М4 Guest phone   0000ХХХХ  Record new GSM PIN code, where   ХХХХ   — new PIN code.  0000 ХХХХ    GSMPSWХХХХ   GSMPSW ХХХ    0050XXXXYYYY  Record new emergency disarm code, where  XXXX   — current code;   YYYY   — new code.  0050 XXXX YYYY    PINXXXXYYYY  PIN XXXX YYYY    0001XYXXX  Record new М1 phone number, where: where  X   — alert call at alarm (1 —On, 0 — Off);   Y   — SMS alert at alarm (1 — On, 0 — Off);   XXX   — new phone number in international format +75555555555. М1 phone number can not be deleted.  0001 XY XXX    M1XYXXX   M1 XY XXX    0002XYXXX    Record new М2 phone number, where: where  X   — alert call at alarm (1 —On, 0 — Off);   Y   — SMS alert at alarm (1 — On, 0 — Off);   XXX   — new phone number in international format +75555555555. If XY parameters not entered, then current M2 number will be deleted.  0002 XY XXX   M2 XY XXX    M2XYXXX    0003XYXXX    Record new М3 phone number, where: where  X   — alert call at alarm (1 —On, 0 — Off);   Y   — SMS alert at alarm (1 — On, 0 — Off);   XXX   — new phone number in international format +75555555555. If XY parameters not entered, then current M3 number will be deleted.  0003 XY XXX    M3XYXXX   M3 XY XXX    0004XYXXX    Record new М4 phone number, where: where  X   — alert call at alarm (1 —On, 0 — Off);   Y   — SMS alert at alarm (1 — On, 0 — Off);   XXX   — new phone number in international format +75555555555. If XY parameters not entered, then current M4 number will be deleted.  0004 XY XXX    M4XYXXX   M4 XY XXX    ZZZZ9900PINXYXXX  Emergency changing M1 phone number:   ZZZZ   — GSM PIN code;   PIN   — emergency disarm code; X   — alert call at alarm (1 — On, 0 — Off);   Y   — SMS alert at alarm (1 — On, 0 — Off);   XXX   — new phone number in international format +75555555555. This command can be sent from any phone number.  ZZZZ 9900 PIN XY ХХХ    ZZZZEM1PINXYXXX    009401  Enable all control commands for М2 as forМ1  М2+    009400  Disable all control commands for М2 as for M1  М2-    009500  Enable control commands from guest phone  GUEST+    009501  Disable control commands from guest phone  GUEST-    00961  Enable GSM PIN request forМ1  M1PSW+    00960  Disable GSM PIN request forМ1  M1PSW-   APN?  Request active SIM card APN  APN NAME LOGIN PSW  Record APN for active SIM card, where:   NAME   —  APN name (mandatory parameter)   LOGIN PSW   — login and password for access (optional parameters). If no any parameters entered, then current APN settings will be deleted.   00520  Disable notification on switching to roaming   00521  Enable notification on switching to roaming   00522  Enable notification on switching to roaming with automatic data internet off   00523  Enable data internet in roaming   00524  Disable data internet in roaming  0069Х  Setting interval of forwarding all incoming SMS from unregistered numbers and USSD from cell carrier to M1 phone, where:   X   — interval in min (1 - 60 min).  FORWARD X  Voice call commands Voice menu command Function М1 М2, М3, М4 Guest phone  61   Enable interior listening for 4 min or until owner hang up a phone call. Switching SIM cards Text commands Function М1 М2, М3, М4 Guest phones  SIMMAIN X  Record priority SIM card, where:   X   — priority operation SIM card (0 — no priority SIM card, both are equal; 1 — 1st SIM is main, 2nd SIM card is supplementary; 2 — 2nd SIM is main, 1st SIM card is supplementary). Value 1 is set as default.  SIMMAIN?  Request current SIM cards priority  SIMNUM?  Request operating SIM cards number Accessories registration Registration mode is used to pair new remote keys, tags, smartphones and other wireless and wired accessories to the system main unit. To prevent unauthorized registration of new accessories, entry to registration mode is permitted in Disarmed mode only. If Immobilizer mode enabled then authorization must be passed to fully disarm a system. Tags and smartphones shall be registered in one registration cycle. All previously paired tags and smartphones will be deleted from memory if not paired again together with the new ones. Total amount of accessories can be registered in the system main unit: 5 wireless tags / 4 smartphones / 4 remote keys / 4 service relay modules / 8 wireless sensors Total up to 8 Bluetooth accessories can be operated simultaneously, where: 1 memory cell is always reserved for registered smartphone. 7 cells are reserved for other wireless devices (tags, wireless relays and sensors). Once 8 first detected Bluetooth accessories are in range, then remaining registered Bluetooth accessories will be ignored until any of first devices get out of range. Entry to accessories registration Disarm system if it is armed.   Switch ignition Off if it is On Push service button or external transceiver button 7 times. Switch ignition On. 7 LED flashes and 7 beep sounds shall follow. Entry into registration mode will be confirmed with 2 LED flashes and 2 beep sounds. Wireless tags (transponders) registration Remove battery from a tag slot. Push and hold tag button and insert battery back in slot observing the right polarity (“+” side top). The tag LED will light up red. Release button and make sure a tag LED serial red flashes come up for 10 seconds. Successful registration will be confirmed by a tag LED green flash, 2 service button LED flashes and 2 beep sounds. If a tag pairing failed then its LED will light up red. Repeat items 1-3 for the remaining tags.   Smartphone registration Enable Bluetooth in smartphone and activate device searching Select “StarLine B9” in available devices list Enter pairing code 000000 (for iOS click “Pair”) Remote key registration Push 1 and 2 remote key buttons shortly In 3 sec successful registration will be confirmed with remote key short beep, 2 service button LED flashes and 2 sounds. If registration failed, then 4 beep sounds will follow. Repeat items 1, 2 for remaining remote keys. Exit from the device registration mode System will automatically exit from accessories registration mode in 5 minutes or at ignition switch Off. Exit from registration mode is confirmed with 2 service button LED flashes, 2 sounds and followed with a serial sounds in a number of total registered accessories. Owner authorization code (PIN-to-Drive) Pin-to-Drive code entered with factory buttons is used for secondary owner authorization at disarming and immobilizer mode. Recording and changing authorization PIN code in registration mode: Disarm system if it is armed. Switch ignition Off if it is On. Push service button or external transceiver button 7 times. Switch ignition On. 7 LED flashes and 7 beep sounds shall follow. Entry into registration mode will be confirmed with 2 LED flashes and 2 beep sounds. Enter a new PIN code with use of supported factory buttons with 3 sec and less intervals. Each pushing will be indicated with one LED flash. Authorization PIN code may consist of 2 to 25 push sequence of factory buttons. List of supported factory buttons is published at can.starline.ru for each supported vehicle. If pushing a button is not indicated with a LED flash, then this button is not supported via CAN bus. 7. Code entry will be confirmed in 3 sec with 2 LED flashes and 2 beep sounds. 8. Enter a new Pin code once again. 9. Properly repeated new code entry will be confirmed with 2 LED flashes and 2 beep sounds. Invalid code entry is followed with 4 LED flashes and 4 sounds, then repeat 5...8 steps. 10. Switch ignition Off within 10 sec to exit registration mode. 11. Exit from registration mode will be confirmed with 2 LED flashes and 2 beep sounds. Deleting authorization PIN code Disarm system if it is armed Switch ignition Off if it is On Push service button or external transceiver button 7 times. Switch ignition On. 7 LED flashes and 7 beep sounds shall follow. Entry into registration mode will be confirmed with 2 LED flashes and 2 sounds. Push service button 3 times. Wait for the long LED light up confirming that existing authorization PIN code has been erased from memory. Switch ignition Off. Exit from registration mode will be confirmed with 2 LED flashes and 2 beep sounds. Emergency disarming System can be fully disarmed with emergency disarm code, indicated on owner ID card, when: Tag is lost Tag or remote key battery discharged Anti hijack mode is activated Emergency disarming with service button Make sure ignition is switched On. Push service button or external transceiver button a number of times, equal to the first digit of emergency disarm code.       Each digit entry will be confirmed within 3 sec with service button LED flashes in a number equal to a sequence number of corresponding digit entered (1,2, 3 or 4 times). 4. Repeat 1...2 steps for remaining digits. 5. Valid code entry is confirmed with 3 flashes and 3 sounds, system turns disarm. If invalid emergency disarm code is entered 3 times, then next entry shall be blocked for 15 min. Each button push in this interval will be indicated with 5 flashes. Example of entry the code 5342 Emergency disarming with SMS text message Send SMS text command  30 XXXX , where ХХХХ — emergency disarm code from ID card. Changing emergency disarm code with service button (or external transceiver button) Switch system in disarmed mode if it is armed. Push service button 4 times. Switch ignition On. 4 LED flashes and 4 sounds shall follow. Entry into code recording will be confirmed with 2 LED flashes and 2 sounds. If nothing is done withing 5 sec system shall turn Off emergency code recording mode. 5. Switch ignition Off. 6. Switch ignition On and push service button a number of times equal to a first digit of existing emergency disarm code. 7. Switch ignition Off. Each digit entry will be confirmed with LED flashes equal to a sequence number of corresponding digit entered (1,2, 3 or 4 times). 8. Repeat 6...7 steps for remaining digits. 9. Valid existing code entry will be confirmed with 2 LED flashes and 2 beep sounds. 10. Switch ignition On. Push service button a number of times equal to a first digit of a new emergency disarm code. 11. Switch ignition Off. Each digit entry will be confirmed with LED flashes equal to a sequence number of corresponding digit entered (1, 2, 3 or 4 times). 12. Repeat 10...12 steps for remaining new code digits. 13. A new code entry will be confirmed with 2 LED flashes and 2 beep sounds. 14. Enter a new code once again repeating 10...12 steps. 15. New emergency disarm code recording will be confirmed with 2 LED flashes and 2 beep sounds. Connection diagram Firmware Find description for the main unit, remote key, and tag firmware versions by the link: Firmware