| **Icons** | **Meaning** |
|---|---|
|  | Engine is running |
|  | Automatic engine start by timer enabled |
|  | Periodic automatic engine start enabled |
|  | Automatic engine start by temperature enabled |
|  | Automatic engine start by battery voltage drop enabled |
|  | Program neutral executed |
|  | Parking heater activated (blinking) |
| **Icons** | **Meaning** |
|---|---|
|  | Armed |
|  | Hands-Free mode |
|  | Service mode |
|  | Programming mode |
|  | Buttons lock |
|  | Anti-hijack mode |
| **Icons** | **Meaning** |
|---|---|
|  | Ignition switched On |
|  | Parking brake tighten |
|  | Hood open |
|  | Door open |
|  | Trunk open |
| **Icons** | **Meaning** |
|---|---|
|  | Motion or tilt sensors triggered |
|  | Auxiliary sensor 1 triggered |
|  | Auxiliary sensor 2 triggered |
|  | Tilt sensor triggered |
|  | Motion sensor triggered |
|  | Shock sensor warning level triggered |
|  | Alarm level of shock sensor triggered |
|  | Shock sensor disabled |
| **Icons** | **Meaning** |
|---|---|
|  | Data transfer |
|  | Replace remote battery |
|  | Siren sounds enabled |
|  | Siren sounds disabled |
| Short Push | Pushing one or two buttons once less than 1,5 sec. Example:  — first button short push;  — short push of first and second buttons simultaneously. |
|---|---|
| Long Press | Pushing and holding a button or two buttons until melody and vibration come up.
2 levels of a long pushing are envisaged:
• 1 level long push – push and hold until a first melody.
Example:  — 1 button long push;  — 1 and 2 buttons long push simultaneously;
- 2 level long push — push and hold until a second melody;
Example:  — 4 button long push of a 2 level.
|
| Double push | Double push of one button within 1 sec. Example:  — double push of 1 button. |
| Triple push | Triple push of one button within 1 sec. Example:  — triple push of 1 button. |
| Sequential push | Double push of one or two buttons with different duration. First pushing is long (1 or 2 level) and second push is short. Firs button must be released before pushing next button. Example:  — sequential pushing 2 and 1 buttons. |
| Commands | Button combinations |
|---|---|
| Arm |  |
| Silent arming |  |
| Disarm |  |
| Silent disarming |  |
| Request vehicle statuses (engine and cabin temperature, battery voltage, fuel level). At remote start – remaining engine run time. |  |
| Start engine |  |
| Stop engine |  |
| Start parking heater |  |
| Stop parking heater |  |
| Find car on parking |  |
| Switch shock sensor On / Off |  |
| Switch motion / tilt sensor On / Off |  |
| Enable Panic |  |
| Unlock trunk |  |
| Enable automatic engine start | configuration menu |
| Enable / disable Service mode |  or configuration menu |
| Enable / disable Hands free mode | configuration menu |
| Enable/disable buttons lock |  |
| Enable/disable auto buttons lock |  |
| Enable vibration only |  |
| Enable sound profile 2 |  |
| Enable sound profile 1 |  |
| Enable sound profile 0 |  |
| Enable sound profile -- |  |
| Activate Flexible Logic program |  |
| **Icons** | **Parameters** | **Description** | **Tune step** |
|---|---|---|---|
 | Hands Free mode | Enable/disable Hands Free mode | — |
 | Automatic engine and parking heater start by timer | Set engine start hour and min. Engine and parking heater autostart settings are switched with short pushing buttons  and . Engine start settings are indicated with digit 1, parking heater settings – with digit 2. | 1 min |
 | Periodic engine start | Set engine start interval in hours | 1 hour |
 | Automatic engine start by temperature | Set engine start temperature in Celsius degrees | 1 ºС |
 | Automatic engine start by battery voltage | Set main storage battery voltage limit in Volts | 0,1 V |
 | Service mode | Enable/disable service mode | — |
Current time is automatically retrieved from cellular network and satellites data (if GPS module is available).
##### **Setting lights and siren indication at Arming and Disarming** Select 2 item of Settings menu and set the mode with and  buttons: 0 – hidden mode without siren and lights indication 1 – silent mode with lights indication only 2 – full mode with siren and lights indication 3 – only siren indication ##### **Setting siren volume at Arming and Disarming** Select 3 item of Settings menu and set siren volume level with  and  buttons: 0 — silent mode, 10 — max volume ##### **Setting lights and siren indication in Alarm mode** Select 4 item of Settings menu and set the mode with and  buttons: 0 – hidden mode without lights and siren indication 1 – silent mode with lights indication only 2 – full mode with lights and siren indication ##### **Setting siren volume setup in Alarm mode** Select 5 item of Settings menu and set siren volume level with  and  buttons: 0 — silent mode, 10 — max volume ##### **Setting motion sensor sensitivity** Select 6 item of Settings menu and set sensor sensitivity from 0 to 30 level with  and  buttons: 0 - motion sensor is disabled, 30 – max sensitivity ##### **Setting tilt sensor sensitivity** Select 7 item of Settings menu and set sensor sensitivity from 0 to 30 level with  and  buttons: 0 – tilt sensor is disabled, 30 – max sensitivity ##### **Setting shock sensor warning level sensitivity** Select 8 item of Settings menu and set sensor sensitivity from 0 to 30 level with  and  buttons: 0 – warning level shock sensor is disabled, 30 – max sensitivity The warning shock sensor sensitivity must be set over the main shock sensor level. ##### **Setting shock sensor main alarm level sensitivity** Select 9 item of Settings menu and set sensor sensitivity from 0 to 30 level with  and  buttons: 0 – main alarm shock sensor is disabled, 30 – max sensitivity The main alarm shock sensor sensitivity must be set below the warning shock sensor level. ##### **Setting tag (transponder) loss range** Select 10 item of Settings menu and set tag loss range value from 3 to 10 level with  and  buttons: 3 – min distance, 10 – max distance ##### **Setting tag (transponder) detection range** Select 11 item of Settings menu and set tag detection range value from 1 to 8 level with  and  buttons: 1 – min distance, 8 – max distanceTag detection range must be set less than a tag loss range.
##### **Setting remote key connection control** Select 12 item of Settings menu and set connection control period to 1 or 2 value with  and  buttons: 0 – connection control is disabled, 1 – connection check every 3 min ##### **Setting turbotimer run time** Select 13 item of Settings menu and set turbotimer run time from 1 to 5 min with  and  buttons.Remote engine start must be enabled in system configuration parameters for this option.
##### ##### **Setting remote / automatic engine start duration** Select 14 item of Settings menu and set engine run time from 10 to 60 min with  and  buttons. ##### **Settings max duration of extended remote / automatic engine start** Select 15 item of Settings menu and set extended engine run time from 15 to 60 min with  and  buttons. ##### **Setting parking heater starting max duration** Select 16 item of Settings menu and set max parking heater starting interval from 1 to 10 min with  and  buttons. ##### **Setting parking heater run time duration** Select 17 item of Settings menu and set parking heater run time from 5 to 60 min with  and  buttons. ##### **Setting parking heater activation before remote engine start** Select 18 item of Settings menu and set parking heater activation before remote engine start with  and  buttons: 0 – do not start parking heater 1 - start parking heater before remote engine start ##### **Setting parking heater activation before automatic engine start** Select 19 item of Settings menu and set parking heater activation before automatic engine start with  and  buttons: 0 – do not start parking 1 - start parking heater before automatic engine start ##### **Settings temperature for parking heater activation before remote and automatic engine start** Select 20 item of Settings menu and set parking heater activation temperature before remote and automatic engine start from –5 to –30 ºС with  and  buttons. ##### **Setting temperature for automatic engine start** Select 21 item of Settings menu and set automatic engine start temperature from +10 to –40 ºС with  and  buttons. ##### **Setting 2 way remote key detection range** Select 22 item of Settings menu and set remote key detection range from 1 to 10 level with  and  buttons: 1 – min distance, 10 – max distance. ### **Sound profile menu** Sound profiles menu contains settings for commands confirmation, alarm trigger and buttons pushing. Profiles are selected with following buttons combination:| **№** | **Profile** | **Button combination** | **Description (at default settings)** |
|---|---|---|---|
| 1 | SOUND 2 | [](https://help.starline.ru/uploads/images/gallery/2023-11/icon-short-1.png) | All signals at max level and vibration enabled. |
| 2 | SOUND 1 |  | All signals at min level and vibration enabled. |
| 3 | SOUND 0 |  | Vibration only, all sounds Off |
| 4 | SOUND - |  | Fully silent, vibration and all sounds Off |