Control with 2-way remote key (optional accessory) LCD remote control and matching external RF868 transceiver are optional accessories and can be ordered from local dealer. Display icons meaning Remote engine start Icons Meaning Engine is running Automatic engine start by timer enabled Periodic automatic engine start enabled Automatic engine start by temperature enabled Automatic engine start by battery voltage drop enabled Program neutral executed Parking heater activated (blinking) Operating Modes Icons Meaning Armed Hands-Free mode Service mode Programming mode Buttons lock Anti-hijack mode Secured zones Icons Meaning Ignition switched On Parking brake tighten Hood open Door open Trunk open Sensors Icons Meaning Motion or tilt sensors triggered Auxiliary sensor 1 triggered Auxiliary sensor 2 triggered Tilt sensor triggered Motion sensor triggered Shock sensor warning level triggered Alarm level of shock sensor triggered Shock sensor disabled Additional indicators Icons Meaning Data transfer Replace remote battery Siren sounds enabled Siren sounds disabled Control commands Definition of buttons push duration Short Push Pushing one or two buttons once less than 1,5 sec. Example:   — first button short push; — short push of first and second buttons simultaneously. Long Press Pushing and holding a button or two buttons until melody and vibration come up. 2 levels of a long pushing are envisaged: • 1 level long push – push and hold until a first melody.  Example:  — 1 button long push; — 1 and 2 buttons long push simultaneously; 2 level long push — push and hold until a second melody; Example:  — 4 button long push of a 2 level. Double push Double push of one button within 1 sec. Example: — double push of 1 button. Triple push Triple push of one button within 1 sec. Example: — triple push of 1 button. Sequential push Double push of one or two buttons with different duration. First pushing is long (1 or 2 level) and second push is short. Firs button must be released before pushing next button. Example: — sequential pushing 2 and 1 buttons. Control commands Commands Button combinations Arm Silent arming Disarm Silent disarming Request vehicle statuses (engine and cabin temperature, battery voltage, fuel level). At remote start – remaining engine run time. Start engine Stop engine Start parking heater Stop parking heater Find car on parking Switch shock sensor On / Off Switch motion / tilt sensor On / Off Enable Panic Unlock trunk Enable automatic engine start configuration menu Enable / disable Service mode or configuration menu Enable / disable Hands free mode configuration menu Enable/disable buttons lock Enable/disable auto buttons lock Enable vibration only Enable sound profile 2  Enable sound profile 1 Enable sound profile 0 Enable sound profile -- Activate Flexible Logic program Modes menu Some options and operation modes are controlled in Modes menu: Hands Free mode, Service mode, Autostart settings. Modes menu is entered and exited with 4 button long push level 1: . Modes menu is automatically exited when no any buttons pushed 15 sec.  Modes submenu is flipped with or buttons short push forward and backward accordingly. Submenu options are selected with 2 and 3 buttons short push:  .   Parameters are tuned with and  buttons short push up and down accordingly. Long buttons pushing increases parameters tuning speed. Listing menu points, changing settings and menu exit are confirmed with melody.   Icons Parameters Description Tune step Hands Free mode Enable / disable Hands Free mode — Automatic engine and parking heater start by timer Set engine start hour and min. Engine and parking heater autostart settings are switched with short pushing buttons  and . Engine start settings are indicated with digit 1, parking heater settings – with digit 2. 1 min Periodic engine start Set engine start interval in hours 1 hour Automatic engine start by temperature Set engine start temperature in Celsius degrees 1 ºС Automatic engine start by battery voltage Set main storage battery voltage limit in Volts 0,1 V Service mode Enable / disable service mode — Settings Menu Operation parameters are set in the Setting menu. Settings menu is entered and exited with 4 button long push level 2:  .  1 — parameter function number 2 — parameter value Operation menu points are flipped with and  buttons up and down accordingly. Parameters are tuned with and buttons short push up and down accordingly. Long buttons pushing increases parameters tuning speed. Listing menu points, changing settings and menu exit are confirmed with melody. Time zone setup Select 1 item of Settings menu and set matching time zone with   and     buttons. Current time is automatically retrieved from cellular network and satellites data (if GPS module is available).   Setting lights and siren indication at Arming and Disarming Select 2 item of Settings menu and set the mode with and   buttons: 0 – hidden mode without siren and lights indication 1 – silent mode with lights indication only 2 – full mode with siren and lights indication                                                                                                                                          3 – only siren indication Setting siren volume at Arming and Disarming Select 3 item of Settings menu and set siren volume level with and buttons: 0 — silent mode, 10 — max volume  Setting lights and siren indication in Alarm mode Select 4 item of Settings menu and set the mode with and buttons: 0 – hidden mode without lights and siren indication 1 – silent mode with lights indication only 2 – full mode with lights and siren indication Setting siren volume setup in Alarm mode   Select 5 item of Settings menu and set siren volume level with  and buttons: 0 — silent mode, 10 — max volume Setting motion sensor sensitivity Select 6 item of Settings menu and set sensor sensitivity from 0 to 30 level with  and buttons: 0 - motion sensor is disabled, 30 – max sensitivity Setting tilt sensor sensitivity Select 7 item of Settings menu and set sensor sensitivity from 0 to 30 level with and buttons: 0 – tilt sensor is disabled, 30 – max sensitivity Setting shock sensor warning level sensitivity Select 8 item of Settings menu and set sensor sensitivity from 0 to 30 level with  and buttons: 0 – warning level shock sensor is disabled, 30 – max sensitivity The warning shock sensor sensitivity must be set over the main shock sensor level. Setting shock sensor main alarm level sensitivity Select 9 item of Settings menu and set sensor sensitivity from 0 to 30 level with and buttons: 0 – main alarm shock sensor is disabled, 30 – max sensitivity The main alarm shock sensor sensitivity must be set below the warning shock sensor level. Setting tag (transponder) loss range Select 10 item of Settings menu and set tag loss range value from 3 to 10 level with  and buttons: 3 – min distance, 10 – max distance Setting tag (transponder) detection range Select 11 item of Settings menu and set tag detection range value from 1 to 8 level with  and buttons: 1 – min distance, 8 – max distance Tag detection range must be set less than a tag loss range.   Setting remote key connection control Select 12 item of Settings menu and set connection control period to 1 or 2 value with and buttons: 0 – connection control is disabled, 1 – connection check every 3 min Setting turbotimer run time Select 13 item of Settings menu and set turbotimer run time from 1 to 5 min with and buttons. Remote engine start must be enabled in system configuration parameters for this option.   Setting remote / automatic engine start duration Select 14 item of Settings menu and set engine run time from 10 to 60 min with and buttons.  Settings max duration of extended remote / automatic engine start Select 15 item of Settings menu and set extended engine run time from 15 to 60 min with  and buttons.  Setting parking heater starting max duration Select 16 item of Settings menu and set max parking heater starting interval from 1 to 10 min with and buttons. Setting parking heater run time duration Select 17 item of Settings menu and set parking heater run time from 5 to 60 min with   and buttons. Setting parking heater activation before remote engine start Select 18 item of Settings menu and set parking heater activation before remote engine start with and buttons: 0 – do not start parking heater 1 - start parking heater before remote engine start Setting parking heater activation before automatic engine start Select 19 item of Settings menu and set parking heater activation before automatic engine start with and buttons: 0 – do not start parking 1 - start parking heater before automatic engine start Settings temperature for parking heater activation before remote and automatic engine start Select 20 item of Settings menu and set parking heater activation temperature before remote and automatic engine start from –5 to –30 ºС with and buttons. Setting temperature for automatic engine start Select 21 item of Settings menu and set automatic engine start temperature from +10 to –40 ºС with and buttons. Setting 2 way remote key detection range Select 22 item of Settings menu and set remote key detection range from 1 to 10 level with and buttons: 1 – min distance, 10 – max distance. Sound profile menu Sound profiles menu contains settings for commands confirmation, alarm trigger and buttons pushing. Profiles are selected with following buttons combination: № Profile  Button combination Description (at default settings) 1 SOUND 2 All signals at max level and vibration enabled. 2 SOUND 1 All signals at min level and vibration enabled. 3 SOUND 0 Vibration only, all sounds Off 4 SOUND - Fully silent, vibration and all sounds Off Changing sound profile settings Sound profile menu is entered with long pushing level 2. Setting commands confirmation signals   1 — selected signal type volume level 2 — selected sound profile number  3 — commands confirmation sound settings icon 4 — vibration:  — enabled,  — disabled Sounds volume is tuned with and buttons short push. Vibration is enabled and disabled with button short push. Next sound signal type is flipped with  button short push. Setting alarm sounds volume 1 — Selected signal type volume level; 2 — Selected sound profile number; 3 — Vibration:  — enabled, — disabled; 4 — Alarm sounds volume settings icon. Sounds volume is tuned with or  buttons short push. Vibration is enabled and disabled with  button short push. Next sound signal type is flipped with button short push. Setting buttons push sound volume 1 — buttons sound volume setting icon 2 — selected volume 3 — selected sound profile 4 — vibration:  - enebled,  - disaabled Sounds volume is tuned with or  buttons short push.  Vibration is enabled and disabled with button short push.  Next sound signal type is flipped with button short push.  Sound profile settings menu is automatically exited in 10 sec if no any buttons pushed. After exit the set sound profile is indicated for several sec. Resetting sound profile to factory default settings Select the necessary sound profile with corresponding buttons combination. Enter sounds profile menu with long pushing level 2. Hold 3 button until next sound signal . Setting sounds tone The sounds tone can be also setup in sounds profile menu. Enter to sounds profile menu with long pushing level 2. Push buttons  shortly. The current sounds tone St-1 or St-2 shall be displayed. St-1 tone is set as default. Push buttons    shortly to select next tone.  Sounds tone menu is automatically exited in 10 sec if no any buttons pushed.   Buttons auto lock The option locks buttons automatically each time after backlit off. It is enabled and disabled with long push  level 2. Remote key searching Push and hold service (valet) button for 5 sec – remote key shall beep.