User manual

StarLine wireless transponder card (hereinafter referred to as the card) is designed to control the vehicle security system functions using the secure Bluetooth Smart protocol. The card is supplied from factory in transport (power saving) mode, i.e. inactive! To switch it to normal operating mode, press the card button 5 times, followed by 3 short beeps. 

 

 

 TECHNICAL SPECIFICATION 

 

 

 

 

 

 

 Radio range 

 

 

 Bluetooth 2.4 GHz 

 

 

 

 

 Power supply 

 

 

 Built in Li-pol battery 3.7 V 

 130 mAh 

 

 

 

 

 Battery runtime 

 

 

 up to 4 months 

 

 

 

 

 Battery charge time 

 

 

 up to 2 hours 

 

 

 

 

 Operation temperature 

 

 

 0 ... 40 C 0 

 

 

 

 

 Waterproof rating 

 

 

 IP65 

 

 

 

 

 Dimensions 

 

 

 85 x 54 x 2 mm 

 

 

 

 

 Weight 

 

 

 13 gr 

 

 

 

 

 PAIRING CARD IN SECURITY SYSTEM 

 The main unit firmware version must be 2.42 and above 

 1. When security systems is disarmed and ignition Off, press the service button 7 times and switch IGN On. Entry to registration mode will be confirmed by 7 flashes of the service button LED and 7 beeps of the main unit built-in buzzer. 

 2. Press the card button 7 times, wait for a 2-second beep during which press the button once briefly. 

 During pairing process the card emits short sounds: 

 1 short beep – pairing successful 

 2 short beeps – pairing failed 

 3. Switch IGN Off 

 Exiting registration mode will be confirmed by 2 flashes of the service button LED and 2 beeps of the main unit built-in buzzer. And then followed by a number of beeps corresponding to the number of registered devices. 

 Transponders and smartphones must be all paired in one registration cycle. All previously paired transponders and smartphones will be deleted from memory 

 USING THE TRANSPONDER CARD 

 

 

 

 Duration of a card button pressing: 

 short – press and release button, followed by a sound of corresponding current operation mode; 

 long – press and hold button until a long beep 

 Duration of long pressing can be of 2 levels: 

 1 level — press and hold button followed by beeps of current operating mode and then long beep, during which the button must be released. 

 2 level — press and hold button followed by beeps of current operating mode and a long beep, then followed by serial beeps, during which the button must be released. 

 

 

 

 

 

 

 

 

 

 

 Commands 

 

 

 Button press 

 sequence 

 

 

 Sounds 

 

 

 

 

 

 Arm / disarm 

 

 

 1 short press 

 

 

 1 short 

 

 

 

 

 Anti-hijack 

 switch On / Off 

 

 

 long press 1 level 

 

 

 2 short 

 

 

 

 

 Service mode 

 switch On / Off 

 

 

 long press 2 level 

 

 

 3 short 

 

 

 

 

 NOTE! To save card from damaging, recommend carrying it in a wallet or card holder 

 Device contains an irreplaceable lithium battery. Do not disassemble, break, or burn the card, or expose it to moisture, direct sunlight, low air pressure, or extreme temperatures below 0 °C or above 65 °C.   Use only original charging cable. If the card overheats, swells up, or fails to charge, stop using it immediately 

 CHARGING 

 

 Connect the charger magnetic plug to the card contacts. The built-in LED will be blinking white.  When battery is fully charged, the LED will lit permanently and turn off once charger is unplugged. 

 

 When connecting or disconnecting charger, card indicates a charge level with sounds: 

 

 

 

 

 Sound signals 

 

 

 Charge level 

 

 

 

 

 1 short 

 

 < 25% 

 

 

 

 2 short 

 

 >= 25% 

 

 

 

 3 short 

 

 >= 50% 

 

 

 

 4 short 

 

 >= 75% 

 

 

 

 1 long 

 

 = 100% 

 

 

 

 

 Do not dispose the faulty and broken transponder card along with a regular household waste. It must be disposed at a designated electric and electronic appliances collection point