StarLine M66 v2 Safety precautions Attention! Read the manual before using the security system. Pay special attention to sections marked with . To check if this security system is suitable for your vehicle, follow vehicle manual and manufacturer requirements. StarLine security system is a complex technical device that connects to vehicle wiring and equipment, including engine controls.  It must be installed only by qualified, trained auto electronics technicians who have passed safety training. Configured parameters must comply with vehicle manual requirements. The user is fully responsible for any damage to people, animals, or property resulting from improper use of security system or violation of safety precautions in this manual. Manufacturer is not responsible for losses or injuries caused by breaching these safety rules. If your system includes a wireless tag (transponder), follow these recommendations: do not carry a tag with vehicle's original keys always switch system to service mode before handing over a vehicle for maintenance or car wash do not give tags to other people to prevent unauthorized access to security functions keep tags out of reach of children and animals store the spare tag and battery in the vehicle in its original factory packaging Safety precautions when charging vehicle storage battery Battery charging applies voltage above the normal 12V/24V to battery and vehicle circuits, which can damage factory electronics and optional equipment. Do NOT use chargers or jump-starters directly on the vehicle without disconnecting the battery terminals in these modes: rapid charging with high current ("boost" or similar modes) START modes for engine starting Never use starting/charging devices for engine starting if main battery is disconnected, main battery is faulty (short circuits, broken plates, etc.). Never use faulty charging devices, and other power supply equipment (i.e. welding inverters), not dedicated to charge 12V and 24V vehicle batteries. Avoid the "light up" method of starting with using cables from a donor vehicle battery. The owner is fully responsible for short circuits, voltage surges, or damage to security system and vehicle electronics.  Follow a safe storage battery charging procedure! Before charging a battery terminals must be disconnected from vehicle circuits. After charging, connect battery terminals back to vehicle circuits. This is necessary because battery health (internal shorts, plate damage, etc.) can't be checked without special equipment. Connecting a charger to a faulty battery risks over voltage damage to vehicle electronics and security system. General Description StarLine M66 v2 security and telematic system (hereinafter referred to as the system) is dedicated to securing various types of vehicles from theft and robbery. It matches 12V and 24V onboard power systems, interacts with vehicle systems through the CAN bus, brings multilevel digital and analog immobilising functionality, and provides subscription free GSM and GPS live tracking and remote control at   starline.online web service and StarLine mobile app. The systems can be controlled using the wireless tag, SMS commands, voice call menu, StarLine mobile app, or at starline.online monitoring service. Owner is authorised with a personal ID tag through the Bluetooth Smart encrypted protocol or a PIN code entered by standard buttons. Major benefits  embedded 2G GSM or 4G LTE modem and 2* nanoSIM card slots 2*CAN bus data interfaces for easy and quick integration into the modern vehicles onboard network  «Super Slave» option for automatic arming and disarming with use of a factory key or Keyless-Go driver authentication by wireless tag, or smartphone paired via Bluetooth Smart (this functionality can be limited by a phone operating system configuration and not guaranteed) authorisation with PIN-to-Drive code (entered via standard vehicle buttons) is supported over CAN bus GPS location, live tracking, and remote control via the lifetime-free StarLine web service and mobile app live vehicle data monitoring: i.e. battery voltage, mileage, fuel level, distance to empty etc. live OBDII diagnostics and trouble codes displayed in the app drive behavior analyzing and scoring trip data storage in non-volatile memory (“black box”): up to 1,000 km urban and 5,000 km highway driving, up to 13,000 events optional StarLine R6 wireless relay module to control hood lock, siren, engine kill, engine temperature, and bonnet trigger switch universal programmable input and output channels FlexibleLogic - customised operation logic based on "Event - Term - Action" program scripts universal StarLine Master installer’s software for the system configuration and updating through USB and Bluetooth interface compact housing for convenient and hidden installation Technical Specification Parameter Values Cellular network bands 2G version: GPRS 850, 900, 1800, 1900 4G version: GPRS 900, 1800, LTE B1, B3, B5, B7, B8, B20 Antenna type Embedded GPS / GLONASS receiver sensitivity – 148 dBm —«cold start» – 163 dBm —«hot start» – 165 dBm — in tracking Short range control Bluetooth Low Energy 2.4 GHz Interfaces • 2xCAN • 1 x microUSB • 4 programmable channels which can be set as:      • 1 positive input       • 1 negative input       • 3 OC outputs - 0.2 A       • 1 x StarLine data bus Input voltage  8 – 32 V Rated current within 25 mA Bluetooth tag current 32.7 μA Operating temperature  −40 °С ... +85 °С Tag protection rating IP67 Dimensions 64 х 44 х 13.5 mm Weight 33 g Personal information Delivery set includes a sticker with following data: • device main unit serial number • one-time activation code • service code • emergency disarm code Remove protection layer from the sticker carefully. Do not use metal and other sharp items to avoid occasional erasing a printed information under protection layer. Do not share emergency disarm code and service code with anybody to avoid your vehicle security breach! Due to security reasons the service and emergency disarm codes are generated randomly at factory, never stored in any database and therefore cannot be recovered once lost! A system main unit with lost service code and emergency disarm code cannot be normally used and must be replaced to a new one. Strongly recommend to copy it in a safe place and record in StarLine mobile app: “Settings” - “General information” - “Device codes” GSM control and GPS navigation StarLine.online and mobile app StarLine system can be remotely controlled and monitored on the starline.online web tracking platform and StarLine mobile app with life time free subscription. Make sure that a proper local SIM card with active balance, internet traffic and permission to operate with M2M smart devices is installed and configured at installation. SIM card boot PIN code must be disabled prior to inserting into the main unit.  Make sure the local network support cellular standards and bands described in device technical specification. 1. Download StarLine 2 mobile app from your phone store (App Store, Google Play, Huawei AppGallery) or browse starline.online web tracking service 2. Register a new or sign in to existing StarLine account 3. Go to " Device adding " ("+" button) menu on the main screen, select " Add new device " — Next — " GSM module, alarm system, smart tracker " — " Use activation code " 4. Enter the one-time activation code printed on attached sticker 5. System will be registered on server and appear in device list on the main screen Activation code can not be used again to add device into another account. Use SMS command 00581 and the one-time PIN code in this case.       Cellular commands System can be controlled with voice and SMS text commands from the owner master phone number (M1) and additional registered numbers (M2, M3, M4). The first incoming call telephone number shall be automatically recorded as M1 master number. All commands received from M1 number are executed without a GSM PIN code in default configuration. PIN code is recorded by owner at initial call from M1 number. Also, this number sets up control permissions for M2, M3, and M4 phones. Commands from guest phones are executed with PIN code in the beginning, i.e. system arming command: 1234 11; where 1234 – PIN code, 11 – arming command number. If invalid password is entered twice from the guest number, commands from that number will be blocked for 1 hour, and alert message will be sent to the owner's M1 number Voice call commands Command Function М1  М2, М3, М4 Guest phones   0  Listen commands menu   10  Disarming   101  Silent disarming   11  Arming   111  Silent arming   12  Arming with shock sensor disabled   13  Arming with auxuliary sensor disabled   14  Arming with shock sensor warning level disabled   15  Arming with tilt sensor disabled   31  Activate Anti-hijack mode   40  Request location   41  Request vehicle state   50  Disable Service mode   51  Enable service mode   70  Disable Hands Free   71  Enable Hands Free SMS text commands Text commands Function М1 М2, М3, М4 Guest phones   10  Disarming  ARM-   О-    101  Silent disarming   11   Arming  ARM+   О+    111  Silent arming   12  Arming with shock sensors disabled   13   Arming with auxuliary sensor disabled   14  Arming with shock sensor warning level disabled   15  Arming with tilt sensor disabled   19  Panic activation   PANIC    40  Request location   GPS    41  Request vehicle state   AUTO    45  Request cell connection status and SIM card balance   BALANCE    MONEY  30 ХХХХ  Emergency disarming,  where  XXXX    - emergency disarm code from sticker with codes in your manual.  A- ХХХХ    31  Activate Anti-hijack mode  А+    50  Disable Service mode  S-    51  Enable Service mode  S+    69  Activate video recorder (dashcam)   VIDEOREG    70  Disable Hands Free  R-    71  Enable Hands Free  R+   VALIDATOR-  Reset PIN-to-Drive code by factory buttons  8N  Activate FlexibleLogic program, where N – program number    SETTING+  Enter configuration via BLE  SETTING-  Exit configuration via BLE  FWUPDATE VER LANG  Firmware update via internet, where VER – firmware version number (can be written without dots, optional parameter) LANG — firmware language version (optional parameter): EN, FR, DE, ES, IT, RU If no any parameter added, then the latest release version and same language firmware is uploaded  FWUPDATE STOP  Stop firmware update via internet  FWUPDATE?  Request status of firmware updating via internet Info commands Text commands Function М1 М2, М3, М4 Guest phone  REG ХХХХ  Entering "Device Registration" mode, where XXXX - emergency disarm code                 05  Request registered accessories list  REG?    06  Request current GSM PIN code  GSMPSW?    07  Request registered master phone numbers   TEL    PHONES    09   Request GSM signal strength, battery voltage, firmware version status   INFO  GSM settings commands Text commands Function М1 М2, М3, М4 Guest phone   0000ХХХХ  Record new GSM PIN code, where   ХХХХ   — new PIN code.  0000 ХХХХ    GSMPSWХХХХ   GSMPSW ХХХ    0050XXXXYYYY  Record new emergency disarm code, where  XXXX   — current code;   YYYY   — new code.  0050 XXXX YYYY    PINXXXXYYYY  PIN XXXX YYYY    0001XYXXX  Record new М1 phone number, where: where  X   — alert call at alarm (1 —On, 0 — Off);   Y   — SMS alert at alarm (1 — On, 0 — Off);   XXX   — new phone number in international format +75555555555. М1 phone number can not be deleted.  0001 XY XXX    M1XYXXX   M1 XY XXX    0002XYXXX  Record new М2 phone number, where:   X   — alert call at alarm (1 —On, 0 — Off);   Y   — SMS alert at alarm (1 — On, 0 — Off);   XXX   — new phone number in international format +75555555555. If XY parameters and phone number not entered, then current M2 number will be deleted.  0002 XY XXX   M2 XY XXX    M2XYXXX    0003XYXXX    Record new М3 phone number, where: where  X   — alert call at alarm (1 —On, 0 — Off);   Y   — SMS alert at alarm (1 — On, 0 — Off);   XXX   — new phone number in international format +75555555555. If XY parameters and phone number not entered, then current M3 number will be deleted.  0003 XY XXX    M3XYXXX   M3 XY XXX    0004XYXXX    Record new М4 phone number, where: where  X   — alert call at alarm (1 —On, 0 — Off);   Y   — SMS alert at alarm (1 — On, 0 — Off);   XXX   — new phone number in international format +75555555555. If XY parameters and phone number not entered, then current M4 number will be deleted.  0004 XY XXX    M4XYXXX   M4 XY XXX    ZZZZ9900PINXYXXX  Emergency changing M1 phone number:   ZZZZ   — GSM PIN code;   PIN   — emergency disarm code; X   — alert call at alarm (1 — On, 0 — Off);   Y   — SMS alert at alarm (1 — On, 0 — Off);   XXX   — new phone number in international format +75555555555. This command can be sent from any phone number.  ZZZZ 9900 PIN XY ХХХ    ZZZZEM1PINXYXXX    009401  Enable all control commands for М2 as forМ1  М2+    009400  Disable all control commands for М2 as for M1  М2-    009500  Enable control commands from guest phones  GUEST+    009501  Disable control commands from guest phones  GUEST-    00961  Enable GSM PIN request for М1  M1PSW+    00960  Disable GSM PIN request for М1  M1PSW-   APN?  Request active SIM card APN  APN NAME LOGIN PSW  Record APN for active SIM card, where:   NAME   —  APN name (mandatory parameter)   LOGIN PSW   — login and password for access (optional parameters). If no any parameters entered, then current APN settings will be deleted.   00520  Disable notification on switching to roaming   00521  Enable notification on switching to roaming   00522  Enable notification on switching to roaming with automatic data internet off   00523  Enable data internet in roaming   00524  Disable data internet in roaming  0069Х  Setting interval of forwarding all incoming SMS from unregistered numbers and USSD from cell carrier to M1 phone, where:   X   — interval in min (1 - 60 min).  FORWARD X  SIM cards switching Text command Function М1 М2, М3, М4 Guest phones  SIMMAIN X  Record priority SIM card, where:   X   — priority operation SIM card (0 — no priority SIM card, both are equal; 1 — 1st SIM is main, 2nd SIM card is supplementary; 2 — 2nd SIM is main, 1st SIM card is supplementary). Value 1 is set as default.  SIMMAIN?  Request current SIM cards priority  SIMNUM?  Request operating SIM cards number Periodic connection mode control (Beacon mode) Text command Function M1 М2, М3, М4 Guest phone  MAYAK+  Enable periodic connection mode (Beacon mode)  MAYAK-  Disable periodic connection mode (Beacon mode) Auxiliary commands Text command Function M1 М2, М3, М4 Guest phone  K1+  Universal output №1 On  K1-  Universal output №1 Off  K2+  Universal output №2 On  K2-  Universal output №2 Off  K3+  Universal output №3 On  K3-  Universal output №3 Off Control with wireless tag (transponder) Wireless tags availability depends on delivery set The included and optional tags are supplied from factory in transport (power saving) mode, i.e. inactive! Pushing a tag button in this mode is indicated by green and red alternating flashes of the built-in LED. To switch it to normal mode push a tag button several times until flashing color turns to green . Connection check Push button once to check tag connection status. 2 LED flashes means connection with security main unit established, 1 flash means disconnected. A flash color corresponds to the current active mode: green - regular mode, Anti-hijack is disabled  red - Anti-hijack mode is enabled yellow - Service mode is enabled Control over security system Duration of a tag button pushing: short – push and release button, followed with a flash of corresponding current operation mode long–push and hold button until LED begins flashing Duration of long push are of 2 levels: 1 level – push and hold a tag button followed with double short flashes of current operating mode and then long flash at which button must be released 2 level – push and hold a tag button followed with double short flashes of current operating mode, then one long flash  and then followed with serial flashes at which button must be released Command Button push Arm and Disarm 1 short Enable and disable Anti-hijack by tag away long 1 level Enable and Disable Service mode long 2 level Replacing a tag battery Wireless tag (transponder) is equipped with CR2032 3V battery. Tag battery discharging is indicated with 3 sounds of external buzzer (or siren) at ignition On and owner is notified with text message to his phone number. Then battery must be replaced as soon as possible To replace battery open a tag casing carefully with a flat metal or plastic item, remove discharged battery from slot. Install a new battery in the slot observing correct polarity (positive side up, as shown on picture).  Do not forget remove safety sticker from a new battery. A smartphone with support of Bluetooth 4.2 and above can also be used as a tag. See Devices registration article to pair a smartphone as a tag. Operation modes Security modes Armed Disarmed Anti-hijack Alarm Panic Supplementary modes «Slave» Hands Free Service mode Registration Configuration Armed Mode The following zones are controlled in armed mode: ignition shock sensor tilt sensor motion sensor If any protected zone is triggered, the system switches to Alarm mode. System can be armed when ignition off only. If arming command received at ignition on, then only doors are locked System is armed in one of following ways: pushing tag button once in disarmed or alarm mode SMS text command  11   voice call menu command  11   command from StarLine mobile app command from  starline.online web account arming with factory security system in Slave mode tag loss or touching capacitive sensor in Hands Free mode  System shall confirm arming with 1 lights flash and 1 siren sound. Disarmed mode System is disarmed by one of following ways: pushing tag button once in armed mode SMS text command  10  voice call menu command  10   command from StarLine mobile app command from starline.online web account disarming with factory security system in Slave mode tag detection or touching capacitive sensor in Hands Free mode Disarming is confirmed with 2 siren sounds and 2 lights flashed. If alarm was triggered while armed mode then 3 siren sounds and 3 lights flashes come up at disarming. Automatic doors lock on a trip System can automatically lock doors on a trip on a trip by one of selected terms:  ignition is switched On vehicle starts moving and brake pedal pressed parking brake released automatic transmission is shifted from parking position preset vehicle speed is reached Automatic doors unlock on a trip System can automatically unlock doors on a trip by one of selected terms: ignition is switched Off automatic transmission is shifted to parking position engine is stopped ignition is switched Off and automatic transmission is shifted to parking positioning parking brake is tighten Automatic doors lock / unlock option can be configured in StarLine mobile app or starline.online account  Trunk unlock in armed mode Owner can unlock and open trunk by means of a factory remote in armed mode once StarLine tag is visible in detection range.  Unlock trunk in Armed mode" option is configured by installer during setup Keyless-Go system blocking The option of factory Keyless-Go blocking via CAN bus secures against factory key stealing and relay attack with specific radio hacking devices. The system shall lock factory Keyless-Go system once StarLine tag is out of detection range. And then unlocks it once tag is detected again in range. This option is disabled by default and must be enabled in system configuration if needed. Owner authorisation with a tag must be enabled as well. Find out if the option is supported for your vehicle via CAN bus at can.starline.bz Alarm mode Alarm shall trigger when any of secured zones is breached in armed mode. System activates siren alert sound, hazards lights flashing for 30 seconds and notifies owner with phone call, text message, and notification in StarLine2 app. If breached zone is not restored system repeats alert cycle once again. Any warning zone breaching is followed with 3 lights flashes and 3 siren sounds. Alarm mode can be aborted in Armed mode with push of a tag button. Alert methods can be set in mobile app or at starline.online: siren and hazard lights hazard lights only no visual or sound alerts Siren volume level in Alarm mode can be set in mobile app or starline.online web service, when siren is connected to R6 relay module The output channel must be set on siren (or horn) control in system configuration with StarLine Master program to enable sound alerts. Siren must be connected through automotive relay 12V or 24V The maximum number of zone triggering is limited to 8 times within 1 security cycle Panic mode Panic mode ensures owner and vehicle security and informs on intrusion attempt. This mode can also be used to easily locate vehicle in a parking lot. Mode can be activated with text message  19 or a command from StarLine mobile app. System shall activate siren alert and hazard lights flashing for 10 sec in order to scare an intruder and attract other people attention. Anti-hijack mode Anti-hijack mode secures driver against assault attempts on a trip. The mode is activated either by owner command or by a tag loss on a trip. Anti-hijack by owner command is activated by one of following ways: SMS text message  31   voice call menu command  31   command from StarLine mobile app command from starline.online personal account The mode operation algorithm depends on a vehicle speed reading from CAN bus (check on can.starline.ru  website) System enables warning sounds and lights on upcoming engine blocking for 10 seconds. Then by reaching a speed below 30 km/h engine will be safely stopped. If CAN bus speed reading support is missing, the system will activate warning sounds and lights on upcoming engine blocking for 10 seconds after receiving the command. The engine will be blocked either after 3 minutes or  after pressing the brake pedal . Exit from Anti-hijack mode is done by one of following ways: SMS text command  30 XXXX , where XXXX - emergency disarm code entering emergency disarm code using the standard vehicle buttons entering emergency disarm code by opening a driver door  at starline.online personal account with entering emergency disarm code In case of invalid emergency disarm code is entered 3 times, then a code entry will be blocked for 15 min and owner will be informed with text message. Anti-hijack by a tag loss on a trip The mode operation algorithm depends on a vehicle speed reading from CAN bus.  Anti-hijack operation sequence when speed supported from CAN bus: any of secured zones has been breached (doors, hood or trunk) motion sensor has triggered in 30 sec system begins seeking for a tag in another 30 sec, if a tag has not been detected, system enables warning sound and lights for 10 sec by reaching a speed below 30km/h engine will be safely stopped     2. Anti-hijack operation sequence when speed from CAN bus is not supported: any of secured zones has been breached (doors, hood or trunk) motion sensor has triggered in 30 sec system begins seeking for a tag in another 30 sec, if a tag has not been detected, system enables warning sound and lights for 10 sec engine will be stopped in 3 min or after pressing the brake pedal Exit from Anti-hijack mode by a tag loss is made by one of following ways: when tag is detected in range SMS text command  30 XXXX , where XXXX - emergency disarm code disarm command from mobile app or starline.online with entering emergency disarm code  entering emergency disarm code with vehicle standard buttons* entering emergency disarm code by opening a driver door* Check whether the standard buttons and drive door status are supported for your vehicle in CAN bus at can.starline.bz In case of invalid emergency disarm code is entered 3 times, then a code entry will be blocked for 15 min and owner will be informed with text message Anti-hijack by tag loss is disabled by default. Enable it in device settings through mobile app, or press and hold a tag button until red flash come up, then release the button Slave mode Slave mode allows to control security system by means of a factory remote control. System detects unlocking doors and disarming factory security and waits for owner authorisation with any of below methods before disarming itself: Waiting for authorisation starts at any of door, hood and trunk open tag detection in range at disarming within adjusted interval from 15 to 60 sec entering personal PIN code with standard buttons at ignition On within adjusted interval from 15 to 60 sec If authorisation failed by any of methods then system shall activate warning siren sounds and then turn to alarm mode. It is highly recommended to enable above mentioned secondary owner authorization methods in "Slave" mode in system configuration settings To change the owner authorisation method and wait time, contact your installer Service mode Service mode is used for temporary security deactivation and restricting access to system configuration while vehicle maintenance, car wash etc, or when the tag battery is discharged. Service mode can be activated from disarmed state only Following features are disabled in service mode: arming and disarming doors lock and unlock on a trip trunk unlock Hands Free mode Panic mode Anti-hijack by a tag loss main unit calibration trouble codes in CAN information section entry to system configuration entry to device registration   Service mode is enabled by any of following ways: tag button push for over 5 sec until the tag's LED turns yellow SMS text command   51   command from StarLine mobile app or  starline.online account Service mode activation is indicated with a tag LED turned yellow. Service mode is disabled by one of following ways: tag button push for over 5 seconds SMS text command   50   command from StarLine mobile app or  starline.online account After exiting service mode, system switches to disarmed mode and remains in it until tag appears and then disappears from the range Automatic exit from Service mode System automatically turns from service mode to owner authorisation when leaving a service area by selected event when ignition on (set in system configuration while installation).  If authorisation successfully passed then system disarms. If authorisation failed then system triggers alarm. This option requires owner authorisation, embedded sensors and vehicle speed from CAN bus to be enabled in system configuration Immobiliser mode Immobiliser mode prohibits drive without an extra owner authorisation. Depending on settings system waits for owner authorisation with a tag in detection range or PIN code entered with standard vehicle buttons after every disarming or every ignition switching Off and next switching On. In most of vehicles PIN code can be entered with standard buttons only when ignition is switched On. If authorisation is not passed within 1 min, then engine will be stopped at a drive attempt for 1 min or until successful authorisation passed. If the Immobiliser mode is enabled along with Slave mode, both authorisation conditions must be met to disarm the system Video recorder (dashcam) control The option must be initially wired and programmed while installation System can automatically switch dashcam On to begin recording: at ignition switched On – dashcam is activated for 5 min at full alarm or warn alarm triggered – dashcam is activated for 2 min with SMS command  69  dashcam is activated for 5min If engine is still running in armed mode then dashcam continues operating until engine is stopped Emergency braking alert In case of emergency braking system can alert the other traffic participants by means of hazard lights blinking.  Hazard lights turn off in 5 sec after the end of sudden braking, or beginning of acceleration.  The option is to be set in the system configuration. The main unit embedded accelerometer must be calibrated for the function proper operation (make sure the corresponding option is enabled in system configuration) Device registration Registration mode is used to pair tags, smartphones and wireless relay StarLine R6.  To prevent unauthorized registration of new accessories, entry to registration mode is permitted in Disarmed mode only. If Immobiliser mode enabled then authorization must be passed to fully disarm a system Tags and smartphones shall be registered in one registration cycle. All previously paired tags and smartphones (except for StarLine R6 relay module) will be deleted from memory if not paired again together with the new ones Total amount of accessories can be registered in the system main unit: 5 wireless tags or 4 smartphones Complete all device registration steps without long pauses between them Entry to device registration disarm system if it is armed send SMS command REG ХХХХ , where  ХХХХ is emergency disarm code wait for SMS message confirming entry to registration mode If invalid emergency disarm code is sent 3 times, then entry to device registration will be blocked for 15 min, and alert SMS will be sent to owner's M1 phone number Wireless tags (transponders) registration Remove battery from a tag slot Push and hold tag button and insert battery back in slot observing the right polarity (“+” side top). The tag LED will light up red Release button and make sure a tag LED serial red flashes come up for 10 seconds Successful registration will be confirmed by a tag LED green flash and SMS message.  If a tag pairing failed then its LED will light up red Repeat items 1-3 for the remaining tags Smartphone registration enable Bluetooth in smartphone and activate device searching select "StarLine M66 v2" in available devices list enter pairing code 000000 (for iOS click "Pair") If multiple registered smartphones are in range at the same time, the system will only work with the first one to connect Exit from the device registration mode System will automatically exit from device registration mode in 5 minutes. Successful device registration will be confirmed by an SMS with a list of registered devices. Owner authorisation code (PIN-to-Drive) Pin-to-Drive code entered with standard vehicle's buttons is used for secondary owner authorisation at disarming. If owner has not authorised within 1 min, engine will be blocked for 1 min at attempt to start it or until successful authorisation passed. The secondary authorisation method and interval are selected in the system configuration by installer Recommend connect external buzzer or siren for the code entry sound confirmation Entering PIN-to-Drive authorisation code: Disarm system if it is armed Switch ignition On The series of triple sounds of external buzzer will follow. System is waiting for the code entry Enter PIN code by a sequence of vehicle's standard buttons pressing with no more than 3 sec push intervals  presses. 5. If valid code entered, 2 buzzer beeps come up and system shall disarm.  If invalid code entered, then series of triple beeps continues - retry code entry from step 3 The owner's authorisation code consists of a button sequence with 2 to 30 presses of the standard vehicle buttons. See the list of supported standard buttons on the can.starline.bz If no sound signal follows after pressing the factory button, then this button is not supported in this vehicle Recording and changing PIN-to-Drive code Recording (changing) PIN-to-Drive code: Disarm system if it is armed Switch ignition Off   Send SMS text command REG XXXX to enter Registration mode, where XXXX is emergency disarm code Wait for the reply SMS: "Attention! Registration mode activated" Switch ignition On Enter new owner authorisation code by a sequence of vehicle's standard  buttons pressing with no more than 3 sec push intervals Every detected button push shall be followed by a single beep         7. In 3 sec after the full sequence finished system confirms code entry by 2 beeps         8. Enter the same buttons sequence once again         9. Correct button sequence repeated will be confirmed with 2 beeps         Invalid sequence entry will be followed by 4 beeps,         then retry code recording again from step 6         10. Switch ignition Off to exit Registration mode         Emergency disarming System can be fully disarmed with emergency disarm code (find it on the sticker inside printed manual), when: tag is lost or discharged no access to mobile app or starline.online account vehicle is immobilised in Anti-hijack mode Emergency disarming with standard buttons or driver door while armed, switch ignition On - system turns to alarm press and hold brake pedal wait for 2 sec, then press any standard vehicle button (or open and close driver's door) the number of times matching the first digit of emergency disarm code wait for 2 sec and release brake - buzzer or siren (if connected) confirms entry with sounds matching the digit number repeat steps 2 - 4 for remaining digits valid code will be confirmed with 2 sounds and system shall disarm. If invalid code entered, system shall remain in alarm and vehicle immobilised Note! Emergency disarm code and service code are generated randomly at factory and never stored anywhere for security reasons. It cannot be recovered once lost ! Strongly recommend to copy it in a safe place and record in StarLine mobile app: Settings - General information - Device codes If invalid code is entered 3 times, then next attempts will be blocked for 15 min System should be able to read statuses of ignition, brake pedal, at least one standard button or a driver door trigger from CAN bus.  Check your vehicle's CAN bus supported statuses at can.starline.bz Emergency disarming by SMS To emergency disarm, send SMS text command 30 XXXX, where XXXX is emergency disarm code. If invalid code is sent 3 times, then next attempts will be blocked for 15 min, and owner will be notified on it with SMS alert Changing emergency disarm code The current emergency disarm code must be known to change the code Find the factory issued emergency disarm code on the sticked inside printed manual.  The emergency disarm code can use any digits except zero Changing the emergency disarm code by SMS text command To change emergency disarm code, send SMS text command 0050XXXXYYYY, where XXXX - 4 digits of an old code YYYY - 4 digits of a new code. Installation SIM card installation Open main unit housing with a flat metal item. Insert SIM card into the slot on the circuit board. Put the board back in the case. Close the case lid. Tracker placement recommendations The system main unit must be placed so that its cover is pointing towards the sky (StarLine logo side up). Also the unit must not be obscured by metal objects and coatings.  The satellites signal well passes through glass, plastics, decorative door paneling, but does not pass through a metal body, metallized tinting and other metal objects. Connection diagram Black wire - connection to vehicle's ground (-).  This connection must be done first.  Recommend to crimp the wire into the ring terminal and fix it with one of the vehicle's factory ground bolt (screw). Red wire — connection to vehicle's power feed 12 or 24 V.  The wire must be connected to one of the permanently powered contact or wire of 0.5 mm2 thickness at least, or directly to the vehicle's main battery terminal through the supplied 3A protective fuse. Typical connection points: fuse, relay box or body control module (BCM) power supply, ignition switch. Green wire — universal output / input No 1.  Activated by SMS command K1+.  Can be used as an engine kill control, universal output for the other circuits (dashcam, buzzer, siren, PTS button), or input for an auxiliary sensor.  For example, set the output function to Engine blocking in Channel settings and select NO (normally open) or NC (normally closed) connection type in Engine blocking settings of StarLine Master program. Break one of an engine control circuits with automotive relay and connect this output to the control contact. Blue wire — universal output No 2.  Activated by SMS command K2+.  Can be used as an engine kill control, universal output for the other circuits (dashcam, buzzer, PTS button). Yellow wire — can be used for ignition or auxiliary sensor control. White- black wire — can be used as StarLine data bus to connect the other optional StarLine extention devices or as universal output for the other circuits control (dashcam, buzzer, siren, PTS button) The NC (normally closed) engine kill connection type is set by default.   Brown, brown-white, orange and orange-white wires — digital CAN bus interfaces. Find recommended connection points and diagrams for your vehicle at can.starline.bz. The system operation is configured with the help of StarLine Master program.