Controlling the system using a remote key

The presence of a remote key depends on the configuration of the security complex.

Remote Keys

The complex's memory can be programmed with two types of remote keys:

1. Remote key with LCD (liquid crystal display). 
   

      

   The remote key with LCD uses a AAA 1.5 V battery. The battery life of the remote key with LCD is up to 6 months depending on operating conditions.
   

2. Additional remote key.
   
   The additional remote key uses a CR2032 3 V battery.
   The battery life of the additional remote key is up to 1 year depending on operating conditions.

The main and additional remote keys are equivalent in cryptographic resistance. Both remote keys use a dialogue algorithm for data exchange, excluding intelligent electronic hacking.

Information about the current state of the security complex is transmitted to the main remote key and displayed on the screen. The additional remote key does not have notification functions; it is intended only for transmitting basic control commands.

Meaning of icons on the remote key

Engine Start

Icon	Meaning
	Engine is running
	Automatic start by alarm is activated
	Automatic periodic start is activated
	Automatic start by temperature is activated
	Automatic start by battery voltage drop is activated
	Programmed neutral is executed
	Engine heating is activated (blinking)

Operating Modes

Icon	Meaning
	Security on
	"Hands-Free" mode
	Service mode
	Settings and programming mode
	Remote key button lock
	"Anti hijack" mode

Security zones

Icon	Meaning
	Ignition is on
	Parking brake is engaged
	Hood is open
	Door is open
	Trunk is open

Sensors

Icon	Meaning
	Tilt or motion sensor activated
	Additional sensor 1 activated
	Additional sensor 2 activated
	Tilt sensor activated
	Motion sensor activated
	Warning level of shock sensor activated
	Alarm level of shock sensor activated
	Shock sensor is deactivated

Additional Information

Icon	Meaning
	Data Transmission
	Replace battery in remote key
	Siren is on
	Siren is off

Main control commands from remote key

Numbering of buttons on the main remote key:

Numbering of buttons on the additional remote key:

The following terms of button press duration are used in this manual:

Short Press	Pressing a single button (or two buttons simultaneously) for less than 1.5 seconds. Example: — short press of the first button; — short press of buttons 2 and 3 simultaneously.
Long Press	Pressing and holding a button or two buttons until a melodic sound signal and vibration signal appear. Two levels of long press are provided: First-level long press — pressing a button until the first sound signal. Examples: — first-level long press of the first button; — first-level long press of the first and second buttons; Second-level long press — pressing a button until the second sound signal; Examples: — second-level long press of the fourth button.
Double Press	Two presses of the same button within 1 second. Example: — double press of the first button.
Triple Press	Three presses of the same button within 1 second. Example: — triple press of the first button.
Sequential Press	Two presses of one or different buttons. The first press should be long (first or second level), the second press should be short. Release the first button before the second press. Example: — sequential press of buttons 2 and 1.

Main control commands from remote key:

Command	Button Combination
Arm
Arm without confirmation sound signals
Disarm
Disarm without confirmation sound signals
Request engine temperature, cabin temperature, battery voltage, fuel level. During automatic engine start - remaining engine runtime.
Start engine
Stop engine
Activate engine pre-heater
Deactivate engine pre-heater
Search for vehicle in parking lot
Activate/deactivate shock sensor
Activate/deactivate tilt and motion sensor
Activate "Panic" mode
Unlock trunk
Activate automatic start	cursor menu
Activate/deactivate service mode	or cursor menu
Activate/deactivate "Hands-Free" mode	cursor menu
Activate/deactivate button lock
Activate/deactivate "Button Autolock" function
Activate only remote key vibration signal
Activate sound profile "SOUND 2"
Activate sound profile "SOUND 1"
Activate sound profile "SOUND 0"
Activate sound profile "SOUND --"
Launch flexible logic program

Cursor Menu

Some functions of the security complex are controlled through a cursor menu: control of the "Hands-Free" mode, service mode, setting the automatic engine start.

Entering and exiting the menu is done by long-pressing button 4: . If no buttons on the remote key are pressed within 15 seconds, there will be an automatic exit from the menu. When entering the menu, the cursor will be set to the first icon. Transition to the next and previous menu items is done by short pressing buttons or , respectively. 

Selecting a function is done by short pressing buttons 2 and 3: .  Changing the parameter value is done by short pressing buttons or (decrease and increase, respectively). Holding the button for a long time increases the speed of changing the parameter value.

Transitions between menu items, changing parameters, and exiting the menu will be confirmed by a melodic sound signal.

Descriptions and management of settings are provided in the table.

Icon	Parameter	Description	Setting Step
	"Hands-Free" mode	Enable/disable "Hands-Free" mode	—
	Automatic engine start and preheater start by alarm clock	Set the hours and minutes for engine start. Switching between engine and preheater start settings is done by short pressing buttons and on the remote key. When setting the engine start, the screen will display the digit "1", for preheater start — the digit "2".	1 minute
	Automatic start by timer	Set the frequency of engine start in hours	1 hour
	Automatic start by temperature	Set the temperature value in degrees Celsius	1 ºС
	Automatic start by voltage	Set the battery voltage value in Volts	0.1 V
	Service mode	Enable/disable service mode	—

Settings Menu

The settings menu is intended for configuring the complex operation parameters.

Entering and exiting the settings menu is done by long-pressing button 4: . After entering the menu, the current state of the complex settings will appear on the remote key screen:

• 1 — parameter value;
• 2 — parameter number.

Transition to menu items is done by short pressing buttons or , to the previous and next item, respectively.

Decreasing and increasing the parameter value is done by short pressing buttons or , respectively. The longer the press, the more units the value changes.

Changing the parameter and exiting the menu will be confirmed by a melodic sound signal, transitions between menu items — by a vibration signal.

Setting the Time Zone

To set the time zone, select the first item in the settings menu. Then, using buttons  and  set the desired value. The minimum step size is 1 hour.

Setting Light and Sound Indicators for Arming and Disarming

To configure the operation of light and sound indicators when arming and disarming, select the second item in the settings menu. Then, using buttons and   set the desired value.

Description of configuration options:

• for silent arming and disarming (without light and sound indicators), set the value to 0;
• for quiet (only light indication) — value 1;
• for full (light and sound indication) — value 2;
• for using only sound indication — value 3.

Setting Siren Volume for Arming and Disarming

To set the siren volume level, select the third item in the settings menu. Then, using buttons and , select the desired siren volume level.

0 — no sound, 10 — maximum volume level.

Setting Light and Sound Indicators in "Alarm" Mode

To configure light and sound indicators in "Alarm" mode, select the fourth item in the settings menu. Then, using buttons and , set the desired value.

Description of configuration options:

• for hidden indication (without light and sound indicators) set the value to 0;
• for quiet (only light indication) — value 1;
• for full (light and sound indication) — value 2.

Setting Siren Volume in "Alarm" Mode

To set the siren volume in "Alarm" mode, select the fifth item in the settings menu. Then, using buttons and , set the desired siren volume level.

0 — no sound, 10 — maximum volume level.

Setting Motion Sensor Sensitivity

To adjust the motion sensor sensitivity level, select the sixth item in the settings menu. Then, using buttons and , set the desired value from 0 to 30.

0 — sensor disabled, 30 — maximum sensitivity level.

Setting Tilt Sensor Sensitivity

To adjust the tilt sensor sensitivity level, select the seventh item in the settings menu. Then, using buttons and , set the desired value from 0 to 30.

0 — sensor disabled, 30 — maximum sensitivity level.

Setting Warning Shock Sensor Sensitivity

To adjust the pre-warning shock sensor sensitivity level, select the eighth item in the settings menu. Then, using buttons and , set the desired value from 1 to 30.

0 — sensor disabled, 30 — maximum sensitivity level.

The selected pre-warning shock sensor sensitivity value must be greater than the alarm shock sensor sensitivity value.

Setting Alarm Shock Sensor Sensitivity

To adjust the alarm shock sensor sensitivity level, select the ninth item in the settings menu. Then, using buttons and , set the desired value from 0 to 29.

0 — sensor disabled, 29 — maximum sensitivity level.

The selected alarm shock sensor sensitivity value must be lower than the pre-warning shock sensor sensitivity value.

Setting Mark Loss Zone Range

To set the range of the mark loss zone, select the tenth item in the settings menu. Then, using buttons and , set the desired value from 3 to 10.

3 — minimum range, 10 — maximum range.

The mark loss zone range should be greater than the mark detection zone range.

Ensure that the set mark loss zone range is sufficient from all sides of the vehicle.

Setting Mark Detection Zone Range

To set the range of the mark detection zone, select the eleventh item in the settings menu. Then, using buttons and , set the desired value from 1 to 8.

1 — minimum range, 8 — maximum range.

The detection zone should be smaller than the mark loss zone range.

Setting the Communication Check Period with the Remote Key

To set the communication check period with the remote key, select the twelfth item in the settings menu. Then, using buttons and , select the value 0 or 1.

Description of configuration options:

• 0 — communication check disabled;

  • 1 — communication check occurs every 3 minutes.

    
    

Remote Sound Profile Menu

The menu offers 4 sound profiles with settings for various types of remote signals: command confirmation, alarm, and button press. Profile selection is done by pressing buttons on the remote.

The sound profile settings shown in the table are set by default.

№	Profile Name	Button Combination	Description
1	SOUND 2		Maximum volume with all signals, vibration signal enabled.
2	SOUND1		Minimum volume with all signals, vibration signal enabled.
3	SOUND 0		Vibration signal only, sound volume disabled.
4	SOUND --		Silent mode, sound volume and vibration signal disabled.

Adjusting Sound Profile Settings:

Enter the menu by long press of the button . After entering, the current profile settings will be displayed.

Adjusting Command Confirmation Volume

 

• 1 — volume level of the selected signal type;
• 2 — number of the selected sound profile;
• 3 — indication of volume settings for command confirmation signals;
• 4 — vibration signal: — on,  — off.

Volume adjustment is done by short pressing the buttons or , respectively. A short press of the button enables or disables the vibration signal.

To switch to adjusting the next type of signal within the selected sound profile, press .

Adjusting Alarm Signal Volume

• 1 — Selected signal type volume level;
• 2 — Selected Sound Profile Number;
• 3 — Vibration Signal: — on,  — off;
• 4 — Volume Adjustment Indication for Alarm Signals.

Volume adjustment is done by short pressing the buttons or , respectively. A short press of the button enables or disables the vibration signal.

To switch to adjusting the next type of signal within the selected sound profile, press .

Adjusting Button Press Signal Volume

• 1 — Volume Adjustment Indication for Button Presses.
  
• 2 — Selected signal type volume level;
• 3 — Selected Sound Profile Number;
• 4 — Vibration Signal: — on,  — off.

Volume adjustment is done by short pressing the buttons or , respectively. A short press of the button enables or disables the vibration signal.

To switch to adjusting the next type of signal within the selected sound profile, press .

Exiting the menu automatically occurs after 10 seconds without pressing any buttons on the remote. After exiting, the name of the set profile will be displayed on the screen for several seconds:

Resetting Profile Settings to Factory Defaults

To reset profile settings to factory defaults, follow these steps:

1. Select the desired sound profile using the corresponding button combination.
2. Enter the sound profile menu by second-level long press of the 3 button: .
   
3. Repeat the second-level long press of the 3 button: .

Selecting a Sound Theme

In the sound profile menu, you can also set the tone of the remote key's sound signals by selecting one of the sound themes. To select a sound theme, follow these steps:

1. Enter the sound profile menu by performing a second-level long press on button 3: .
2. Briefly press buttons simultaneously. The screen will display the name of the sound theme: BR-1 or BR-2.
3. Briefly press buttons simultaneously to select the next sound theme.

By default, the BR-1 theme is set

You will automatically exit the menu after 10 seconds if no buttons on the remote key are pressed

Automatic Button Lock Function

When this function is activated, the remote key buttons are automatically locked after the backlight turns off. The function is enabled and disabled by performing a second-level long press on buttons 1 and 4: .

Remote Key Locator Function

To locate the remote key, hold the service button for 5 seconds — the remote key will emit a sound signal.

Setting Time and Date

To set the current time and date, follow these steps:

1. Enter the time and date settings menu by sequentially pressing button 4: .
2. Use a short press of button to set the hours and a short press of button to set the minutes.
   

   

   
   
   • 1 — Hours;
   • 2 — Minutes.
3. Briefly press button to proceed to set the current date.
   

   

   
   
   • 1 — Day;
   • 2 — Month;
   • 3 — Year.
4. Use a short press of button to set the current day, a short press of button to set the current month, and a short press of button  to set the current year.
5.  To exit the menu, press buttons  simultaneously.